Datsun Dreaming
Doesnt see what you did
Joined: Sep 2007
Posts: 3,683
Likes: 0
Please hold...
Joined: Jul 2004
Posts: 3,085
Likes: 0
I know, we've used it over the years on misc things for the boats. It just wears out alot faster.
I either have to design them to wear out and be easily replaced (i.e delrin) or built to last and be a total bitch to replace (i.e QA-1)
I'm still leaning towards the QA-1 bearings.
I either have to design them to wear out and be easily replaced (i.e delrin) or built to last and be a total bitch to replace (i.e QA-1)
I'm still leaning towards the QA-1 bearings.
__________________
Team White Car 2010
Team White Car 2010
Doesnt see what you did
Joined: Sep 2007
Posts: 3,683
Likes: 0
Being that you can adjust the delrin spheres, and with the chrome plated ball, I doubt you'll have to replace them very often, and the delrin cups are only $4 a pair if you do actually end up wearing some out.
Do you think I could find a place that would be able to chuck that housing they come with up in a lathe and turn them down to 5/8" thread for the spl rear arms ? I checked with them and they said they dont have plans to offer a 5/8" any time soon
Do you think I could find a place that would be able to chuck that housing they come with up in a lathe and turn them down to 5/8" thread for the spl rear arms ? I checked with them and they said they dont have plans to offer a 5/8" any time soon
Please hold...
Joined: Jul 2004
Posts: 3,085
Likes: 0
I dont know of any machine shops off hand but I'm sure there is some place local that would be able to do it.
The other thing with the delrin cups is they require greasing, and the less maintaince I have to do the better because I'm really lazy with that type of stuff. (I know, I know they have zerk fittings)
The other thing with the delrin cups is they require greasing, and the less maintaince I have to do the better because I'm really lazy with that type of stuff. (I know, I know they have zerk fittings)
__________________
Team White Car 2010
Team White Car 2010
Formerly IThaJokaI
Joined: Jul 2007
Posts: 4,014
Likes: 0
Oh and as far as my wheels, they are +15 effective.. I have a 5mm slip on, or they don't even clear the coil (because I removed all collars but 1.) But like I said, they fit and Ill make them fit better sooner or later.
__________________
Registered User
Joined: Sep 2007
Posts: 4,854
Likes: 0
The JUN AWD HYPER LEMON 350Z R
Yes that thing is sick, The car was built for someone who lives in Hong Kong
CAR FEATURE>> JUN AWD HYPER LEMON 350Z R - Speedhunters
Yes that thing is sick, The car was built for someone who lives in Hong Kong
CAR FEATURE>> JUN AWD HYPER LEMON 350Z R - Speedhunters
kings cannot fall.
Joined: Sep 2004
Posts: 7,784
Likes: 0
S13 has a smaller wheel tub and less room, and my coils are maxed out w/ no collars so the spring sits lower. I'm not having a lot of trouble, its just a close fit. Everyone I know w/ s13s that ran 17x9 +20 fns ran a 215/45 and I did before, but wanted to go 225/45 all around.
but jics apparently have alot of clearance/ small diameter spring.
Electronicals master ;P
Joined: Mar 2005
Posts: 7,408
Likes: 0
. its all in presentationreply to thread, got most of my motor apart aside from pulling the crank and pistons. good thing i was upgrading cams becuase my stocks are fucked along with my rocker arms...
progress:
__________________
Sponsored By Carrabba's
Sponsored By Carrabba'sR.I.P. Tim Aldrich
Electronicals master ;P
Joined: Mar 2005
Posts: 7,408
Likes: 0
oh and someone find some good places for me to order rocker arms and a new oil pump from. nismoshop is the cheapest as of now..
__________________
Sponsored By Carrabba's
Sponsored By Carrabba'sR.I.P. Tim Aldrich
