Datsun Dreaming
Will Drift For Tires
Joined: Dec 2005
Posts: 3,083
Likes: 0
Retired
Joined: Jan 2003
Posts: 5,095
Likes: 0
No worries, I'm headed to Nissan tomorrow to grab a new one and an O-ring while I'm at it.
I finally put some 93 in the tank, finished the heater core lines and put coolant/water in it. Just needs gear oil and p/s fluid. I'll probably finish it off tomorrow after work and drive it around a bit. Idle is weird. It kicks up for a minute then drops down and stalls. I think I have a big vacuum leak some where.
Also can you run the vacuum line from the BOV to one of the smaller two ports on the throttle body? Those two ports lead into basically right where the throttle plate closes. Or should I move it to one of the larger ports that feeds off the middle of the plenum? When the car was running today it sounded like the BOV was stuck open.
I finally put some 93 in the tank, finished the heater core lines and put coolant/water in it. Just needs gear oil and p/s fluid. I'll probably finish it off tomorrow after work and drive it around a bit. Idle is weird. It kicks up for a minute then drops down and stalls. I think I have a big vacuum leak some where.
Also can you run the vacuum line from the BOV to one of the smaller two ports on the throttle body? Those two ports lead into basically right where the throttle plate closes. Or should I move it to one of the larger ports that feeds off the middle of the plenum? When the car was running today it sounded like the BOV was stuck open.
The BOV should feed from a true vacuum port. Those ones that feed right at the throttle plate are for the charcoal canister.
Get that Consult wired up so I can plug into your car.
__________________
(SHIFT-YOUR SHITS WEAK)
Joined: Nov 2006
Posts: 2,356
Likes: 0
pulled my tail lights out i was leaking water into the trunk from them.
advance auto sell the sticky shit that Nissan uses to seal them so spent 45 min cleaning the old and useless shit off and redone with new shouldn't leak anymore
advance auto sell the sticky shit that Nissan uses to seal them so spent 45 min cleaning the old and useless shit off and redone with new shouldn't leak anymore
__________________
Drifting:
most fun you can have
with your pants on.
Drifting:
most fun you can have
with your pants on.
Will Drift For Tires
Joined: Dec 2005
Posts: 3,083
Likes: 0
you wanna come see the motor i have sitting in the bay of a 240 in my garage that is teetering on the bolts because 2 pucks is too short? i dont disagree that it can be done, its simply too short though. by at least 2-3 inches on both sides.
if someone has the actual dimensions i would appreciate it. i'm trying to make my own polyurethane mounts.
if someone has the actual dimensions i would appreciate it. i'm trying to make my own polyurethane mounts.
__________________
Nissan North America - Canton
Nissan North America - Canton
nearly undead
Joined: Jun 2008
Posts: 1,474
Likes: 0
measure the stock mounts?
__________________
live to love the RWD.
89 seafoam coupe w/ SR20 and more- FOR SALE<- click
FAX
______________________________
live to love the RWD.
89 seafoam coupe w/ SR20 and more- FOR SALE<- click
FAX
Please hold...
Joined: Jul 2004
Posts: 3,085
Likes: 0
I'm going to change the BOV vacuum today too, I think its been stuck open.
__________________
Team White Car 2010
Team White Car 2010
Playin Army Man
Joined: Nov 2008
Posts: 61
Likes: 0
well i'm pretty sure that the car you're talkin about in your garage is my old one. and the 2 hockey pucks definitely held the motor very sturdily. i'm not sure what that kid did to the car, but there's no reason the motor should've blown nor those pucks be fucked up.
__________________
aim = bdotmill
aim = bdotmill
