GROUND UP EF hatch build.
StricKly MT 727-510-6301 
Thread Starter
rut roh
Joined: Jan 2006
Posts: 1,665
Likes: 0
Got in a little work today.
Need to get misc nuts and bolts still
Rear coilovers installed along with camber kit and lca's
Also test fit the wheel on for shits and giggles. Going to run 8-10mm spacers all they way around
Need to get misc nuts and bolts still
Rear coilovers installed along with camber kit and lca's
Also test fit the wheel on for shits and giggles. Going to run 8-10mm spacers all they way around
SAVE THE SOHC!
Joined: Sep 2005
Posts: 4,614
Likes: 0
loven it cant wait to see it on the road
__________________
93 del sol si (project)
88 honda cvic ef (daily driver)
hit me up on fb ( www.facebook.com/stewartracing13 )
TR "Old Skool EF" Member #166
93 del sol si (project)
88 honda cvic ef (daily driver)
hit me up on fb ( www.facebook.com/stewartracing13 )
TR "Old Skool EF" Member #166
Thread Starter
rut roh
Joined: Jan 2006
Posts: 1,665
Likes: 0
Thanks guys. Unfortunately didn't get to work on it as much as I hoped to this weekend. Unexpectedly had to drive up to Gainesville to help my friend pull his motor.
Ended up putting it in his apartment until we could bring it to the shop.
and his nice little turbo setup...
However, I did get to putting the front suspension back on. Courtesy of Strictly MT, fresh hardened rubber bushings in the LCA,s and new ARP wheel studs and Honda OEM wheel bearings along with new lower balljoints installed. Also installed the Skunk2 upper control arms.
Ended up putting it in his apartment until we could bring it to the shop.
and his nice little turbo setup...
However, I did get to putting the front suspension back on. Courtesy of Strictly MT, fresh hardened rubber bushings in the LCA,s and new ARP wheel studs and Honda OEM wheel bearings along with new lower balljoints installed. Also installed the Skunk2 upper control arms.
90% grind 10% sleep
Joined: Nov 2002
Posts: 6,963
Likes: 0
Good job Chris..
__________________
727-510-6301
Honda Valve Adjustments 50$
I buy and/or Fix Broken Honda transmissions.
I TUNE KPRO AND S300
I DO NOT WORK FOR FREE
E-Z OUT BOLT AND STUD EXTRACTOR: A tool ten times harder than any known drill bit that snaps neatly off in bolt holes thereby ending any possible future use.
727-510-6301
Honda Valve Adjustments 50$
I buy and/or Fix Broken Honda transmissions.
I TUNE KPRO AND S300
I DO NOT WORK FOR FREE
E-Z OUT BOLT AND STUD EXTRACTOR: A tool ten times harder than any known drill bit that snaps neatly off in bolt holes thereby ending any possible future use.
Thread Starter
rut roh
Joined: Jan 2006
Posts: 1,665
Likes: 0
Finally got a plug for my TP sensor on the ITB's so I did some wiring work today. Removed some misc plugs from the engine harness.
I hope this bundle of wires doesn't scared people off.
Got it a little bit more organized and then went to installing my Type R Engine Stiffner.
I'll most likely finish up this wiring this weekend unless I run back up to Gainesville to help my friend put his motor back in. Shifter should also be installed along with clutch system. Full hydro conversion. Order some tires, race fuel, and start her up.
I hope this bundle of wires doesn't scared people off.
Got it a little bit more organized and then went to installing my Type R Engine Stiffner.
I'll most likely finish up this wiring this weekend unless I run back up to Gainesville to help my friend put his motor back in. Shifter should also be installed along with clutch system. Full hydro conversion. Order some tires, race fuel, and start her up.
