Wtb Sbc 350
Registered User
Joined: Apr 2005
Posts: 625
Likes: 0
I got just about a complete setup with T-5 tranny, just needs some head studs and a bell housing. Its all disassembled, bored .040 over Speed Pro flat top pistons, fresh vortec062 heads, should make 300 or 400 hp. 900 with tranny.
__________________
Need Vinyl Decals/Stickers/Custom Shirts? Pm me. I do them cheap. Almost any design and brand. Or even custom stuff.
Need Vinyl Decals/Stickers/Custom Shirts? Pm me. I do them cheap. Almost any design and brand. Or even custom stuff.
Registered User
Joined: Apr 2005
Posts: 625
Likes: 0
700 for all my motor parts
-2-Bolt Main Bored .040 over
-Vortec 062 Heads (Completely Redone and Never Ran)
-Edelbrock Intake for Votec Heads
-Speed Pro Flat Top Pistons .040 over (6 used, 2 New, All have new rings)
-Stock Rods
-Crankshaft (Remand, Perfect Condition in Block)
-Full Fel-Pro Gasket Set (New)
-Hydraulic Lifters (New)
-Roller Rocks (New)
-Stock Oil Pan (New)
Other Parts:
Used Holley 4-barrel (Needs Rebuild)
2 sets of 350 heads (Need Rebuild)
Box of Random Pistons and Rods
Just had new cam bearings installed and crank installed.
-2-Bolt Main Bored .040 over
-Vortec 062 Heads (Completely Redone and Never Ran)
-Edelbrock Intake for Votec Heads
-Speed Pro Flat Top Pistons .040 over (6 used, 2 New, All have new rings)
-Stock Rods
-Crankshaft (Remand, Perfect Condition in Block)
-Full Fel-Pro Gasket Set (New)
-Hydraulic Lifters (New)
-Roller Rocks (New)
-Stock Oil Pan (New)
Other Parts:
Used Holley 4-barrel (Needs Rebuild)
2 sets of 350 heads (Need Rebuild)
Box of Random Pistons and Rods
Just had new cam bearings installed and crank installed.
__________________
Need Vinyl Decals/Stickers/Custom Shirts? Pm me. I do them cheap. Almost any design and brand. Or even custom stuff.
Need Vinyl Decals/Stickers/Custom Shirts? Pm me. I do them cheap. Almost any design and brand. Or even custom stuff.
Thread Starter
Why So Serious?
Joined: Feb 2005
Posts: 3,242
Likes: 0
700 for all my motor parts
-2-Bolt Main Bored .040 over
-Vortec 062 Heads (Completely Redone and Never Ran)
-Edelbrock Intake for Votec Heads
-Speed Pro Flat Top Pistons .040 over (6 used, 2 New, All have new rings)
-Stock Rods
-Crankshaft (Remand, Perfect Condition in Block)
-Full Fel-Pro Gasket Set (New)
-Hydraulic Lifters (New)
-Roller Rocks (New)
-Stock Oil Pan (New)
Other Parts:
Used Holley 4-barrel (Needs Rebuild)
2 sets of 350 heads (Need Rebuild)
Box of Random Pistons and Rods
Just had new cam bearings installed and crank installed.
-2-Bolt Main Bored .040 over
-Vortec 062 Heads (Completely Redone and Never Ran)
-Edelbrock Intake for Votec Heads
-Speed Pro Flat Top Pistons .040 over (6 used, 2 New, All have new rings)
-Stock Rods
-Crankshaft (Remand, Perfect Condition in Block)
-Full Fel-Pro Gasket Set (New)
-Hydraulic Lifters (New)
-Roller Rocks (New)
-Stock Oil Pan (New)
Other Parts:
Used Holley 4-barrel (Needs Rebuild)
2 sets of 350 heads (Need Rebuild)
Box of Random Pistons and Rods
Just had new cam bearings installed and crank installed.
__________________
No Front Bumper Mafia crew#1 since 04'
The original 350Z Blue 240sx
No Front Bumper Mafia crew#1 since 04'
The original 350Z Blue 240sx
Registered User
Joined: Apr 2005
Posts: 625
Likes: 0
Yes its disassembled. Also comes with chrome timeing cover, timing gears and chain, 4-bolt main caps, and 2 sets of valve covers, but they are side bolt not center so they wont work with the vortecs. Both Chrome, 1 ugly used, one brand new. I put it up for $800 after I really crunched the numbers for the cost, but since I told you $700 i will give it to you for that. LMK if you want pics. Block hasn't been ran since it came out of the machine shop. Just need push rods, camshaft, head bolts, and a few misc. bolt and accesories for a complete engine.
__________________
Need Vinyl Decals/Stickers/Custom Shirts? Pm me. I do them cheap. Almost any design and brand. Or even custom stuff.
Need Vinyl Decals/Stickers/Custom Shirts? Pm me. I do them cheap. Almost any design and brand. Or even custom stuff.
Doesnt see what you did
Joined: Sep 2007
Posts: 3,683
Likes: 0
Have a LT1 longblock, disassembled, $500 with front accessorys except a/c comp, would make you an easy 300-320 HP and dirt cheap with a carb'd intake mani on it.
__________________
R.I.P. Tim 
SR, RB, and LS1 into S13/14 harnesses converted.
SR 13/13- $120, 13/14 or 14/13 $180
RB $200
LS1 $250
full on track cars can take a lot more liberties with shit than a street car. bell bottom kits and crazy wheel fitment look cool sliding on a track, but when i want to drive to taco bus, im going to ruin all of that shit. so it just doesnt work for me. function over fashion.
Originally Posted by osama tim laden
also, im about to blow my moderator status by deleteing all of davids posts
SR, RB, and LS1 into S13/14 harnesses converted.
SR 13/13- $120, 13/14 or 14/13 $180
RB $200
LS1 $250
Registered User
Joined: Aug 2004
Posts: 445
Likes: 0
350 4 bolt all new fs
--------------------------------------------------------------------------------
I have a huge parts list.
all machine work done at pyramid for $1500 on the block and some parts with that price. short block is assembeld,and heads. Ready for your inspection
NEW PARTS:
eagle I beam rods
eagle flat top pistons .60 over
arp rod bolts
arp head bolts
brass freeze plugs
cloyes gear to gear
2 new cams, torker is in it and a more agressive comes with it also
gear to gear timing cover
moroso studed windedge tray installed
scorpion 1.6 roller rockers
comp cams lifters and push rods
moroso valley tray uninstalled
beautifull holly 750 new intake
so much more any questions let me know. 1500$ for every thing including the new stand its on. post here or call me at 727 455 5977 thanks Charlie
--------------------------------------------------------------------------------
I have a huge parts list.
all machine work done at pyramid for $1500 on the block and some parts with that price. short block is assembeld,and heads. Ready for your inspection
NEW PARTS:
eagle I beam rods
eagle flat top pistons .60 over
arp rod bolts
arp head bolts
brass freeze plugs
cloyes gear to gear
2 new cams, torker is in it and a more agressive comes with it also
gear to gear timing cover
moroso studed windedge tray installed
scorpion 1.6 roller rockers
comp cams lifters and push rods
moroso valley tray uninstalled
beautifull holly 750 new intake
so much more any questions let me know. 1500$ for every thing including the new stand its on. post here or call me at 727 455 5977 thanks Charlie
