Which spark plug heat range should I run?
Registered Hater
Thread Starter
Join Date: Aug 2008
Posts: 3,246
Likes: 0
Received 0 Likes
on
0 Posts
Which spark plug heat range should I run?
JDM ITR, I have 2 sets of NGK-R Iridium plugs. One set is 6 and the other is 7. 6 is what was called for by the factory but would I see any benefit running the colder plug (7)?
Some people would go by the color of the insulator as to it
being too hot or too cold.-Bob
being too hot or too cold.-Bob
__________________
Keystone Motor Club (Founded 2012)... Free car show Every 3rd Saturday, newsletter is
https://www.tamparacing.com/forums/e...-car-club.html
Keystone Facebook ...click: "Keystone Motor Car Club"
Port Richey Rod Run at Coast Buick GMC Coming May 25 2024
https://carstoshow.com/registerevent.aspx?eventid=99114
50's Diner US19.... A Florida Attraction.
1730 US-19, Holiday Fl 34691 click: https://www.tamparacing.com/forums/t...-racing.html CHRA sanctioned cruise-in.
Cruise-In; Free; Every Saturday 5-8PM plus 10% off the whole menu to cruisers
All Cars Every 2nd Saturday Free Breakfast: Since 2015 and more. click: https://www.tamparacing.com/forums/e...ast-tampa.html
Tampa Racing.com covers the Tampa car scene and supports many fund raisers, worthy causes and events that enrich our community. We hope you enjoy them all.
What do I do? ---- on-site *Aftermarket* spring/suspension installations --- on-site impact wrenching---street lowering with your own stock springs...........True Bi-xenon HID projector headlight conversions........ Much more at Bob's Garage!
https://www.tamparacing.com/forums/b...ontact-us.html
https://www.tamparacing.com/forums/b...e-senor-honda/
Keystone Motor Club (Founded 2012)... Free car show Every 3rd Saturday, newsletter is
https://www.tamparacing.com/forums/e...-car-club.html
Keystone Facebook ...click: "Keystone Motor Car Club"
Port Richey Rod Run at Coast Buick GMC Coming May 25 2024
https://carstoshow.com/registerevent.aspx?eventid=99114
50's Diner US19.... A Florida Attraction.
1730 US-19, Holiday Fl 34691 click: https://www.tamparacing.com/forums/t...-racing.html CHRA sanctioned cruise-in.
Cruise-In; Free; Every Saturday 5-8PM plus 10% off the whole menu to cruisers
All Cars Every 2nd Saturday Free Breakfast: Since 2015 and more. click: https://www.tamparacing.com/forums/e...ast-tampa.html
Tampa Racing.com covers the Tampa car scene and supports many fund raisers, worthy causes and events that enrich our community. We hope you enjoy them all.
What do I do? ---- on-site *Aftermarket* spring/suspension installations --- on-site impact wrenching---street lowering with your own stock springs...........True Bi-xenon HID projector headlight conversions........ Much more at Bob's Garage!
https://www.tamparacing.com/forums/b...ontact-us.html
https://www.tamparacing.com/forums/b...e-senor-honda/
Registered Hater
Thread Starter
Join Date: Aug 2008
Posts: 3,246
Likes: 0
Received 0 Likes
on
0 Posts
Those test used to work good before additives in gas were put into place, still works to an extent. I can read plugs so maybe I should throw the 7's in there and see what they look like after some runs. When I pulled them out before the motor was even started they looked rich.
They original plug was probably a 7 huh. Due to little higher compression and more aggressive fuel/timing maps than a usdm motor.
The 7 will use more fuel, run cooler, and help if you have any detonation.
The 7 will use more fuel, run cooler, and help if you have any detonation.
__________________
Vance @ 863-604-2139 for any questions
Vance @ 863-604-2139 for any questions
Burning cooler will not burn all the gas in the combustion chamber.
__________________
727-510-6301
Honda Valve Adjustments 50$
I buy and/or Fix Broken Honda transmissions.
I TUNE KPRO AND S300
I DO NOT WORK FOR FREE
E-Z OUT BOLT AND STUD EXTRACTOR: A tool ten times harder than any known drill bit that snaps neatly off in bolt holes thereby ending any possible future use.
727-510-6301
Honda Valve Adjustments 50$
I buy and/or Fix Broken Honda transmissions.
I TUNE KPRO AND S300
I DO NOT WORK FOR FREE
E-Z OUT BOLT AND STUD EXTRACTOR: A tool ten times harder than any known drill bit that snaps neatly off in bolt holes thereby ending any possible future use.
Registered Hater
Thread Starter
Join Date: Aug 2008
Posts: 3,246
Likes: 0
Received 0 Likes
on
0 Posts
never thought of that lol I cant remember if the specs I was looking at was for JDM or USDM. Whoever owned it in Japan put in NGK Iridium R 7 heat range.
BKR6E or BKR6EIX. Prefer the BKR6EIX but more expensive
__________________
- Induction Performance
* IP E-Mail
* IP Face Book
* IP Web-Site
* RIP Kevin/Slo_Si RIP & Pablo/Fathead
- Induction Performance
* IP E-Mail
* IP Face Book
* IP Web-Site
* RIP Kevin/Slo_Si RIP & Pablo/Fathead
Registered Hater
Thread Starter
Join Date: Aug 2008
Posts: 3,246
Likes: 0
Received 0 Likes
on
0 Posts
I just looked at the box I'm running BKR6EIX. I dont even remember how much I paid but with how damn expensive my motor is, $40 or so for plugs is nothing lol I wasnt about to take any shortcuts, I want the best in there. Well now I know I'm good with the plugs I put in. And I have an extra set of plugs for different mods later down the road.