how to take out my alternator in my EF

Reply Subscribe

Thread Tools

Jul 30, 2007 | 10:27 PM

#11 (permalink)

senor honda

Registered

Joined: May 2005

Posts: 104,944

Likes: 21

You might try undoing the upper ball joint on Driver side, and dropping down the axle enough to pull the alt out above it.-Bob

__________________
Here is the listings of ALL New Mexico Car Events Including Route 66 Anniversary
https://www.tamparacing.com/forums/t...ar-events.html
Top Car Club Meetings? Click a city
Got a video? Email it to Bobfixesitup@yahoo.com
________________________________________________

Keystone Motor Club (Founded 2012)... Free car show Every 3rd Saturday, newsletter is
https://www.tamparacing.com/forums/e...-car-club.html
Keystone picture gallery is here:
https://carstoshow.com/eventdetails.aspx?eventid=93202

Veterans and Friends on First Saturday...Some pictures....
https://carstoshow.com/registerevent...eventid=102331

Port Richey Rod Run at Coast Buick GMC
https://carstoshow.com/registerevent.aspx?eventid=99114

50's Diner US19.... A Florida Attraction.
1730 US-19, Holiday Fl 34691 click: https://www.tamparacing.com/forums/t...acing.html CHRA sanctioned cruise-in.
Cruise-In; Free; Every Saturday 5-8PM plus 10% off the whole menu to cruisers
50's Diner pictures are here: https://carstoshow.com/eventdetails.aspx?eventid=93194

All Cars Every 2nd Saturday Free Breakfast: Since 2015 and more. click: https://www.tamparacing.com/forums/e...ast-tampa.html

Tampa Racing.com covers the Tampa car scene and supports many fund raisers, worthy causes and events that enrich our community. We hope you enjoy them all.
What do I do? ---- on-site *Aftermarket* spring/suspension installations --- on-site impact wrenching---street lowering with your own stock springs...........True Bi-xenon HID projector headlight conversions........ Much more at Bob's Garage!
https://www.tamparacing.com/forums/b...ontact-us.html
https://www.tamparacing.com/forums/b...e-senor-honda/

Jul 31, 2007 | 05:16 AM

#12 (permalink)

JoKiE crx4294

popeye built!

Joined: May 2005

Posts: 3,114

Likes: 0

removal

Master Cyc. Thats The Easiest By Far Loosen Two Bolts And It Pulls Right Thru The Top

__________________
Can't spell strength without tren

AAS...It's whats for dinner

Jul 31, 2007 | 05:25 AM

#13 (permalink)

F4A22

Old School

Joined: Jun 2003

Posts: 6,217

Likes: 0

Quote:

Originally Posted by gsxr0407

Master Cyc. Thats The Easiest By Far Loosen Two Bolts And It Pulls Right Thru The Top

Jul 31, 2007 | 05:35 AM

#14 (permalink)

Dangelo

Registered User

Joined: May 2007

Posts: 71

Likes: 0

Quote:

Originally Posted by theebluecrx

ive done it that way as well but u can also try jacking the driver side up of the ground so it will drop the axle a little and you should be able to do it that way thats how ive done it before also

__________________

[

Jul 31, 2007 | 12:02 PM

#15 (permalink)

seventhgear

Thread Starter

hanglike sleeve of wizard

Joined: Mar 2003

Posts: 2,252

Likes: 0

Quote:

Originally Posted by Dangelo

ive done it that way as well but u can also try jacking the driver side up of the ground so it will drop the axle a little and you should be able to do it that way thats how ive done it before also

i jacked it up on the drivers side and tried that but again no luck, the axle barely moves.

__________________

image removed from your sig...see forum rules

Jul 31, 2007 | 12:05 PM

#16 (permalink)

seventhgear

Thread Starter

hanglike sleeve of wizard

Joined: Mar 2003

Posts: 2,252

Likes: 0

Quote:

Originally Posted by Old Renegade

you can get it out from the bottom without removing anything, but it is time consuming for it requires a lot of wiggling and shit like that. just take out the axle. why notch your crossmember and possible weaken it.

i was kidding about the notching of the crossmember but i believe i had to notch it n e ways for the rear motor mount to clear and bolt up. so its weakened ne ways

__________________

image removed from your sig...see forum rules

Last edited by seventhgear; Jul 31, 2007 at 01:20 PM.

Jul 31, 2007 | 12:06 PM

#17 (permalink)

rangcrx

engine building &amp;amp;best

Joined: May 2003

Posts: 11,971

Likes: 0

just do it the way i said its very easy

__________________
i love AUTOZONE
MY CAR iS PROTECTED BY ZOOMBAK GPS LOCATOR IS YOURS?

175+served in engines built from minime to gsr/lsvtec,b16 b20vtec,d15 k24 powerhouses or just rebuilds.life is good
i like when people don't take my advice.cause then i make more money when u need it rebuild the right way!

how many speed holes do i need in my bumper,b4 i can run 15's?

Jul 31, 2007 | 01:13 PM

#18 (permalink)

seventhgear

Thread Starter

hanglike sleeve of wizard

Joined: Mar 2003

Posts: 2,252

Likes: 0

Quote:

Originally Posted by rangcrx

easiest way is undo the 2 12mm bolts holding on the master cyl pull it forward and BAMMM pull it right up you will not harm anything i do it amillion times when working on thos cars

but does loosening the bolts and sliding the master cylinder off create any air in the line?

__________________

image removed from your sig...see forum rules

Jul 31, 2007 | 02:21 PM

#19 (permalink)

Dangelo

Registered User

Joined: May 2007

Posts: 71

Likes: 0

man that sucks i know ur frustration been there done that i guesss start taking shit apart is ur only option unless someone is going to travel and help u out!!!

__________________

[

Jul 31, 2007 | 02:36 PM

#20 (permalink)

seventhgear

Thread Starter

hanglike sleeve of wizard

Joined: Mar 2003

Posts: 2,252

Likes: 0

thanks bro ... for now this crx is my only means of transportation due to my mustang being in the shop. so im stuck and need to fix this P.O.S.

SHIT IS HALF APART ALREADY AS OF LAST NIGHT... sry 4 the caps.
but im in limbo now that i hear of this master cylinder take out way to do it. also im in limbo bc i have no garage and the rain is delaying me

__________________

image removed from your sig...see forum rules

Reply Share

First
Prev
2 / 3
Next
Last