Blurbo B16???
Registered User
Joined: Dec 2003
Posts: 1,667
Likes: 0
Originally Posted by LuckyH
I have priced some internals and am thinking of going blurbo for a project car. It's getting to be that time where i am ready to buy some parts for the motor. I have priced out some new Eagle rods for $380, SRP 9:1 pistons for $445. Assuming im only wanting in the 350hp range, would the stock crank be strong enough? Also, i've been told that i should just use the stock rod/main bearings from Honda. I will also be using a block gaurd. The motor will not be bored, only honed and hot tanked. I afraid if I make the cylinder walls any thinner i would have to have it re-sleeved, which im trying to avoid. Well enough rambling, would this setup be on the safe side, im looking to overbuild this motor for what hp i am wanting to run.
Thread Starter
Registered User
Joined: Nov 2002
Posts: 1,507
Likes: 0
Originally Posted by qitstrn
Never had a problem with mine or the other 5 motors that i have built with them.
Also the price i got on the rods included ARP rod bolts. And the price of the pistons didn't include rings, those are $99 for the set.
SickofAlltezzas-
__________________
Chavez Motorsports
Joined: Aug 2003
Posts: 6,385
Likes: 0
DAMN, I can get you a complete set of CP Pistons for less than the SRP's!!! And these are more trusted!
Kris
Kris
__________________
Chavez Motorsports
The reason CMS fabrication is closed!! Click me!
11.965 @ 114 Supercharged Teg...RIP
Chavez Motorsports
The reason CMS fabrication is closed!! Click me!
11.965 @ 114 Supercharged Teg...RIP
35.5 psi, stock sleeves
Joined: Jan 2005
Posts: 1,834
Likes: 0
hrrmm.... <--- Never had a problem w/ srp's. Cp's working fine too. Shouldnt matter if your shooting for 350. Good Luck!
__________________
PUREBRED PERFORMANCE
Fabrication & Tuning Services
813-451-7547 or 813-712-0202
Www.PPETUNED.com <~~ WEBSITE
Curious on honda/acura Ecu Chipping and dyno tuning? Call or visit the website above. Hondata/Neptune/Ectune/Crome Pro. Tuning available for most other systems and platforms as well. DYNOJET
PUREBRED PERFORMANCE
Fabrication & Tuning Services
813-451-7547 or 813-712-0202
Www.PPETUNED.com <~~ WEBSITE
Curious on honda/acura Ecu Chipping and dyno tuning? Call or visit the website above. Hondata/Neptune/Ectune/Crome Pro. Tuning available for most other systems and platforms as well. DYNOJET
Retired Ricer...
Joined: Jan 2003
Posts: 11,813
Likes: 0
I ran SRP pistons in my last motor and they held up just fine... They survived a hell of alot of detonation, and numerous top end runs where everything tends to heat up much more than normal...
I did however go with CPs for my new build just because they are suppose to be a better product, and I got a hell of a deal on them....
I did however go with CPs for my new build just because they are suppose to be a better product, and I got a hell of a deal on them....
__________________
www.facebook.com/chris.storck1
Project WHIPLASH has begun!!!
RacingIntegration.com (813)935-6720
InductionPerformance.com
NS Racing (813)842-5517
www.facebook.com/chris.storck1
Project WHIPLASH has begun!!!
RacingIntegration.com (813)935-6720
InductionPerformance.com
NS Racing (813)842-5517
Chavez Motorsports
Joined: Aug 2003
Posts: 6,385
Likes: 0
Originally Posted by InsaneCivicSedan
I ran SRP pistons in my last motor and they held up just fine... They survived a hell of alot of detonation, and numerous top end runs where everything tends to heat up much more than normal...
I did however go with CPs for my new build just because they are suppose to be a better product, and I got a hell of a deal on them....
I did however go with CPs for my new build just because they are suppose to be a better product, and I got a hell of a deal on them....
$775 with H-beams shipped?
__________________
Chavez Motorsports
The reason CMS fabrication is closed!! Click me!
11.965 @ 114 Supercharged Teg...RIP
Chavez Motorsports
The reason CMS fabrication is closed!! Click me!
11.965 @ 114 Supercharged Teg...RIP
