Can this be fixed???
Thread Starter
Retired Ricer...
Joined: Jan 2003
Posts: 11,813
Likes: 0
Can this be fixed???
Got some rods out of a motor that spun a rod bearing, and wanted to know if any good machine shop (Engine Lab) could fix this???? I was told yes by some folks on Honda Tech, but I want to be sure before I spend the cash.....
This is how it looks...
And this is how it SHOULD look....
Post up if you know... Thanks!!!!
This is how it looks...
And this is how it SHOULD look....
Post up if you know... Thanks!!!!
__________________
www.facebook.com/chris.storck1
Project WHIPLASH has begun!!!
RacingIntegration.com (813)935-6720
InductionPerformance.com
NS Racing (813)842-5517
www.facebook.com/chris.storck1
Project WHIPLASH has begun!!!
RacingIntegration.com (813)935-6720
InductionPerformance.com
NS Racing (813)842-5517
USMC
Joined: Sep 2002
Posts: 10,277
Likes: 0
you should PM tony(0HP930) the link to this thread and ask him.
__________________
TR happily married crew-member #2
___________________
TR happily married crew-member #2
___________________
This is the internet. You're just supposed to talk up whatever you do know as if you're a salesman for it. i.e. I drive a Supra and a Corolla therefore 2JZ is the greatest and so is the 4A and I don't care about anything else because it's all crap since I don't have it. I also have a stack of $20 bills in front of me, therefore 20>50 and 20>100 and 20>1000. $20 bill FTW.
Thread Starter
Retired Ricer...
Joined: Jan 2003
Posts: 11,813
Likes: 0
I posted in General car chat to his attention, so hopefully he will see it... But Ill pm the link anyway.... 
__________________
www.facebook.com/chris.storck1
Project WHIPLASH has begun!!!
RacingIntegration.com (813)935-6720
InductionPerformance.com
NS Racing (813)842-5517
www.facebook.com/chris.storck1
Project WHIPLASH has begun!!!
RacingIntegration.com (813)935-6720
InductionPerformance.com
NS Racing (813)842-5517
Registered User
Joined: Jan 2003
Posts: 5,450
Likes: 0
I would suggest purchasing a new rod to be safe.
__________________
Authorized Dealer & Tuner for: Hondata, eCtune, Neptune, AEM, Crome, Precision Turbo, Omni Power, Walbro, Innovate & more. Dyno Tuning Services, Ecu Chipping, Chipped Ecus, Conversion Harnesses, Widebands, Fuel Injectors, Fuel Pumps, Map Sensors & more.
For more information visit http://www.Phearable.net or call 1-888-236-9831
Authorized Dealer & Tuner for: Hondata, eCtune, Neptune, AEM, Crome, Precision Turbo, Omni Power, Walbro, Innovate & more. Dyno Tuning Services, Ecu Chipping, Chipped Ecus, Conversion Harnesses, Widebands, Fuel Injectors, Fuel Pumps, Map Sensors & more.
For more information visit http://www.Phearable.net or call 1-888-236-9831
engine building &amp;amp;best
Joined: May 2003
Posts: 11,971
Likes: 0
my 2cents on hbeams it will not hurt anything
__________________
i love AUTOZONE
MY CAR iS PROTECTED BY ZOOMBAK GPS LOCATOR IS YOURS?
175+served in engines built from minime to gsr/lsvtec,b16 b20vtec,d15 k24 powerhouses or just rebuilds.life is good
i like when people don't take my advice.cause then i make more money when u need it rebuild the right way!
how many speed holes do i need in my bumper,b4 i can run 15's?
i love AUTOZONE
MY CAR iS PROTECTED BY ZOOMBAK GPS LOCATOR IS YOURS?
175+served in engines built from minime to gsr/lsvtec,b16 b20vtec,d15 k24 powerhouses or just rebuilds.life is good
i like when people don't take my advice.cause then i make more money when u need it rebuild the right way!
how many speed holes do i need in my bumper,b4 i can run 15's?
Thread Starter
Retired Ricer...
Joined: Jan 2003
Posts: 11,813
Likes: 0
How much would it be to just buy one rod??? Im getting a killer deal on these, and Ive been told by a few sources that a good machine shop can fix it, but if its gonna cost me more I might end up just getting the rods new... Im getting these for 175 and they only had 500 miles when it spun the bearing, so I figure if I pay 50 bucks or so to fix it, ill still be comin out on top........
__________________
www.facebook.com/chris.storck1
Project WHIPLASH has begun!!!
RacingIntegration.com (813)935-6720
InductionPerformance.com
NS Racing (813)842-5517
www.facebook.com/chris.storck1
Project WHIPLASH has begun!!!
RacingIntegration.com (813)935-6720
InductionPerformance.com
NS Racing (813)842-5517
bored at work
Joined: Oct 2000
Posts: 4,263
Likes: 0
have it resized which basically means honed to perfect round. For one rod it should only cost 10-20. Then have it mic'd to see if it is in range with the other rods or within a range so a Honda bearing would fit. If it doesn't work you are only out $20 or so.
__________________
Don't bother giving me "rep", I won't return it and I think it is stupid.
Gracie Barra Clearwater Gyms in Clearwater, St. Pete and Port Richey
pm me if you are interested in trying a free class at any of the gyms.
Don't bother giving me "rep", I won't return it and I think it is stupid.
Gracie Barra Clearwater
Gyms in Clearwater, St. Pete and Port Richeypm me if you are interested in trying a free class at any of the gyms.
