Subaru Tech All We'll Drive

FINAL help needed to get car running, pics inside

Thread Tools
 
Old Oct 3, 2005 | 06:38 PM
  #1 (permalink)  
marksaccord95's Avatar
Thread Starter
TR Registered Member #5
 
Joined: Jun 2000
Posts: 7,377
Likes: 0
Default FINAL help needed to get car running, pics inside

1)the vacuum line that comes off the bottom of the TB goes to the BOV right?

2)the harness for the starter to battery, the ground strap with this bracket on the starter side goes to?



3)connector in my hand by the fuse box goes to?


4)wire my thumb is on that comes out of the fuse box goes to?


5) plugs by fuse box. green goes to the pump for the windshield washer, white one goes to?


6)this is on the back right hand side of the motor, almost above the starter. the big vacuum line goes to the tube that runs accross the front of the intercooler, where does this smaller one go?




thanks for any help
__________________
http://www.floridaracing.org



Editor - Stangtv.com - Dragzine.com

2011 Mustang GT Premium 6-speed manual Sterling Gray Metallic - New Project Car
SCT SF3 - FRPP Adjustable Handling Pack - Vortech 597 RWHP 476 lb/ft - 7.5 PSI

1965 Mustang - Blow thru Dart SBF 427ci with a Paxton NOVI-2500
Hydraulic roller, 91 octane, 1030HP

Reply
Old Oct 3, 2005 | 06:40 PM
  #2 (permalink)  
marksaccord95's Avatar
Thread Starter
TR Registered Member #5
 
Joined: Jun 2000
Posts: 7,377
Likes: 0
Default

so close, after i get it running im going to clean everything up.

__________________
http://www.floridaracing.org



Editor - Stangtv.com - Dragzine.com

2011 Mustang GT Premium 6-speed manual Sterling Gray Metallic - New Project Car
SCT SF3 - FRPP Adjustable Handling Pack - Vortech 597 RWHP 476 lb/ft - 7.5 PSI

1965 Mustang - Blow thru Dart SBF 427ci with a Paxton NOVI-2500
Hydraulic roller, 91 octane, 1030HP

Reply
Old Oct 3, 2005 | 07:37 PM
  #3 (permalink)  
QuickOne's Avatar
It's soooo stock?
 
Joined: Jul 2003
Posts: 561
Likes: 0
Default

Originally Posted by marksaccord95
so close, after i get it running im going to clean everything up.

Need hoes clamps on the intake do you.
Reply
Old Oct 3, 2005 | 10:27 PM
  #4 (permalink)  
marksaccord95's Avatar
Thread Starter
TR Registered Member #5
 
Joined: Jun 2000
Posts: 7,377
Likes: 0
Default

yea i gotta go to advanced tomorrow to get that and a few other misc things.
__________________
http://www.floridaracing.org



Editor - Stangtv.com - Dragzine.com

2011 Mustang GT Premium 6-speed manual Sterling Gray Metallic - New Project Car
SCT SF3 - FRPP Adjustable Handling Pack - Vortech 597 RWHP 476 lb/ft - 7.5 PSI

1965 Mustang - Blow thru Dart SBF 427ci with a Paxton NOVI-2500
Hydraulic roller, 91 octane, 1030HP

Reply
Old Oct 4, 2005 | 03:33 AM
  #5 (permalink)  
BrewPuBeaver's Avatar
*Big Schpellar*
 
Joined: Jul 2005
Posts: 3,192
Likes: 0
Default

almost there
__________________
Reply
Old Oct 4, 2005 | 04:06 AM
  #6 (permalink)  
M249SAW's Avatar
Firemedic / Local 4420
 
Joined: Jun 2002
Posts: 1,347
Likes: 0
Default

The BOV vacuum hose attaches to a nipple on the intake manifold.
Attached Thumbnails FINAL help needed to get car running, pics inside-hose.jpg  
Reply
Old Oct 4, 2005 | 04:20 AM
  #7 (permalink)  
M249SAW's Avatar
Firemedic / Local 4420
 
Joined: Jun 2002
Posts: 1,347
Likes: 0
Default

Pic #4 eyelet goes to the stud on the positive battery terminal.

Pic #3 is two wires with a lock washer are ground wires that bolt to the fenderwell (see highlighted part in pic)
Attached Thumbnails FINAL help needed to get car running, pics inside-wire.jpg  
Reply




All times are GMT -8. The time now is 02:15 PM.