ftermarket parts:Eagle,ARP,ACL,Aeromotive,Precision..& ka block & S14 sr S13 parts!!!
ftermarket parts:Eagle,ARP,ACL,Aeromotive,Precision..& ka block & S14 sr S13 parts!!!
I had plans to build this ka but wanna go in a different direction so I need this stuff gone
This is pretty much a complete unassembled motor minus pistons..
KA24DE parts:
-ARP 10mm head studs(brand new still in plasic wrap) SOLD
-Eagle rods w/ ARP 2000 rod bolts(brand new) $275
-ACL race bearings $75 (rod and main)
-Aeromotive fuel pressure regulator $100 (bottom half aluminum finish top half powder coated black w/ rainbow metal flake)
-Top feed rail $100 (powder coated to match regulator)
-S13 valve cover $50(powder coated to match reg. and rail)
-Precision 550cc top feed injectors w/ injector clips(saturated, no need for resistor box) $150
-Complete ka gasket set SOLD
Includes: Head gasket, upper intake manifold gasket, lower intake manifold gasket, egr gasket, iacv gasket, valve cover gasket(s14)
o-rings, every single gasket u can think of is there
-Ka24de block w/ girdle $100(cleaned just needs freeze plugs which are like $5)
-ka24de crank which has been cleaned and looked over $50(good condition)
-Block and crank together $125
I have all the other bolts and parts for the motor as well.. including oil pump water pump ect..EVERYTHING!
-ka24de ported and polished head and port matched intake manifold(not going into details yet due to pending sale)
-S14 SR intake manifold with all sensors, throttle body ect..$90
-3 q45 ignightor chips
w/ plugs $50 each
w/o plugs $30 each
-s13 radio brackets with pocket SOLD
If theres any parts not listed here ask, I may have it..I have lots of parts
Also some pics arent available at the moment because the parts are still at the powder coater
This is pretty much a complete unassembled motor minus pistons..
KA24DE parts:
-ARP 10mm head studs(brand new still in plasic wrap) SOLD
-Eagle rods w/ ARP 2000 rod bolts(brand new) $275
-ACL race bearings $75 (rod and main)
-Aeromotive fuel pressure regulator $100 (bottom half aluminum finish top half powder coated black w/ rainbow metal flake)
-Top feed rail $100 (powder coated to match regulator)
-S13 valve cover $50(powder coated to match reg. and rail)
-Precision 550cc top feed injectors w/ injector clips(saturated, no need for resistor box) $150
-Complete ka gasket set SOLD
Includes: Head gasket, upper intake manifold gasket, lower intake manifold gasket, egr gasket, iacv gasket, valve cover gasket(s14)
o-rings, every single gasket u can think of is there
-Ka24de block w/ girdle $100(cleaned just needs freeze plugs which are like $5)
-ka24de crank which has been cleaned and looked over $50(good condition)
-Block and crank together $125
I have all the other bolts and parts for the motor as well.. including oil pump water pump ect..EVERYTHING!
-ka24de ported and polished head and port matched intake manifold(not going into details yet due to pending sale)
-S14 SR intake manifold with all sensors, throttle body ect..$90
-3 q45 ignightor chips
w/ plugs $50 each
w/o plugs $30 each
-s13 radio brackets with pocket SOLD
If theres any parts not listed here ask, I may have it..I have lots of parts
Also some pics arent available at the moment because the parts are still at the powder coater
__________________
RIP Tim Aldrich
RIP Tim Aldrich
Last edited by quicsilvia; 02-18-2010 at 12:30 PM.