00-05 v6 eclipse turbo kit and built heads
Thread Starter
boosted 3g
Joined: Apr 2009
Posts: 2
Likes: 0
00-05 v6 eclipse turbo kit and built heads
I am putting my car back to stock so I will be selling parts from my car. If you have any questions about the parts shared_pm me.
FS:Custom fabricated v6 turbo kit Asking $3000 without fuel setup OBO
Turbo kit will consist of
-Masterpower T4/T70 .68ar exhaust housing
-2.25 inch stainless steel Y-pipe
-3 inch stainless steel downpipe
-Knockoff Tial wastegate w/5lb spring and a mbc
-XS Power 31x12x3 Intercooler
-2.5 inch aluminum cold side piping
-4 inch inlet pipe
-Greddy type-s bov
-Greddy oil block adaptor
-Oil feed and return line
-Tapped oil pan
Turbo fuel setup $200+shipping OBO
-Autoteg fpr
-450cc low impedance injectors
-Vr4 fuel rails
-Walboro 255lph fuel pump
-Resistor (Will have to be hard wired)
Please Note: This kit will require some modification to the car that it will be installed onto. I will include a custom fabricated intercooler bracket to mount the intercooler and also a support bracket for the turbo. Also will include aem wideband and glowshift egt and boost gauges for a little extra.
Front bank side of the Y-pipe and also the downpipe are heat wrapped.
Turbo inlet side pic
Top of the rear bank of the y-pipe
Bottom of the rear bank of the y-pipe
Bottom side of the front bank
As you can see your crash bar will have to be modified unless you want to
trade this modified crash bar for your stock one.
With the crash bar removed
A piece of sheet metal was removed to get the first intercooler pipe to the intercooler to fit.
Vr4 fuel rails with 450cc injectors
The heads are all stock except for they have rpw stage 1 FI cams and cam gears with ported and polished intake and exhaust ports.
Please Note the heads are in great shape but before I pulled them they did have a lifter tick on start up. So with that said these heads will be needing another set of lifters sooner or later. I will also include the lower intake manifold that is also ported and polished along with the heads. Asking $325+shipping OBO
V6 front bank head
Rear bank head
Front bank head intake ports
rear bank head intake ports
Glowshift boost, and egt gauges that I will include with the kit. I have decided to keep the aem wideband for my next project.
This is almost evertyhing that will come with the kit besides the resistor, fuel pump, oil feed line, greddy oil block adaptor, and the tapped oil pan.
Also this kit will not include the maf that is shown in the picture.
Pic with the intake pipe off of the turbo.
FS:Custom fabricated v6 turbo kit Asking $3000 without fuel setup OBO
Turbo kit will consist of
-Masterpower T4/T70 .68ar exhaust housing
-2.25 inch stainless steel Y-pipe
-3 inch stainless steel downpipe
-Knockoff Tial wastegate w/5lb spring and a mbc
-XS Power 31x12x3 Intercooler
-2.5 inch aluminum cold side piping
-4 inch inlet pipe
-Greddy type-s bov
-Greddy oil block adaptor
-Oil feed and return line
-Tapped oil pan
Turbo fuel setup $200+shipping OBO
-Autoteg fpr
-450cc low impedance injectors
-Vr4 fuel rails
-Walboro 255lph fuel pump
-Resistor (Will have to be hard wired)
Please Note: This kit will require some modification to the car that it will be installed onto. I will include a custom fabricated intercooler bracket to mount the intercooler and also a support bracket for the turbo. Also will include aem wideband and glowshift egt and boost gauges for a little extra.
Front bank side of the Y-pipe and also the downpipe are heat wrapped.
Turbo inlet side pic
Top of the rear bank of the y-pipe
Bottom of the rear bank of the y-pipe
Bottom side of the front bank
As you can see your crash bar will have to be modified unless you want to
trade this modified crash bar for your stock one.
With the crash bar removed
A piece of sheet metal was removed to get the first intercooler pipe to the intercooler to fit.
Vr4 fuel rails with 450cc injectors
The heads are all stock except for they have rpw stage 1 FI cams and cam gears with ported and polished intake and exhaust ports.
Please Note the heads are in great shape but before I pulled them they did have a lifter tick on start up. So with that said these heads will be needing another set of lifters sooner or later. I will also include the lower intake manifold that is also ported and polished along with the heads. Asking $325+shipping OBO
V6 front bank head
Rear bank head
Front bank head intake ports
rear bank head intake ports
Glowshift boost, and egt gauges that I will include with the kit. I have decided to keep the aem wideband for my next project.
This is almost evertyhing that will come with the kit besides the resistor, fuel pump, oil feed line, greddy oil block adaptor, and the tapped oil pan.
Also this kit will not include the maf that is shown in the picture.
Pic with the intake pipe off of the turbo.
