speed limiter on 240?
unprofessional drifter?
Thread Starter
Join Date: Nov 2002
Posts: 113
Likes: 0
Received 0 Likes
on
0 Posts
speed limiter on 240?
Where do I go to get the chip to get rid of this damn speed limiter. I hate it. I was doing 115mph, then all of a sudden it kicks in and I can't go anywhere.
Get the fuck off my lawn
Join Date: Oct 1983
Posts: 11,091
Likes: 0
Received 0 Likes
on
0 Posts
if you are knowledgeable with electronics you can make one yourself using resistors and such from radio shack. a very cheap method if you know what you are doing.
greddy sells a speed cut killer device that is like 3 wires and its around $100 i think. kinda expensive but its like a plug and play thing or maybe just splice in.
its not a mod worth doing unless you will be doing over 115mph often, which isnt legal except at the track. id spend money on other mods to get you those 115mph traps before wasting money on the SCK.
ps - enthalpy made his own i believe, perhaps he can give you a diagram.
greddy sells a speed cut killer device that is like 3 wires and its around $100 i think. kinda expensive but its like a plug and play thing or maybe just splice in.
its not a mod worth doing unless you will be doing over 115mph often, which isnt legal except at the track. id spend money on other mods to get you those 115mph traps before wasting money on the SCK.
ps - enthalpy made his own i believe, perhaps he can give you a diagram.
Senior Member
Join Date: Jun 2000
Posts: 2,649
Likes: 0
Received 0 Likes
on
0 Posts
A nearly stock 240 has no balls whatsoever at 115mph anyway not like it will really pickup any speed in a hurry at that point, not worth it
__________________
92' Nissan 240sx
02' Honda VFR Interceptor
08' Tundra
92' Nissan 240sx
02' Honda VFR Interceptor
08' Tundra
Guest
Posts: n/a
Well when your racing someone on the highway who's just as slow @ 115mph, but they have no limiter.. it's a bitch. 
See... My car, stock, has about the same pull as his up there, but my limiter is 121... so I would pwn him. Damn those Hondas.
See... My car, stock, has about the same pull as his up there, but my limiter is 121... so I would pwn him. Damn those Hondas.
No Ants Drift Member
Join Date: Jun 2000
Posts: 4,117
Likes: 0
Received 0 Likes
on
0 Posts
Originally posted by SR20DET
A nearly stock 240 has no balls whatsoever at 115mph anyway not like it will really pickup any speed in a hurry at that point, not worth it
A nearly stock 240 has no balls whatsoever at 115mph anyway not like it will really pickup any speed in a hurry at that point, not worth it
its an easy mod. there are two ways to do it. above the ECU is a white plug that leads to your gauge cluster. theres a yellow wire with a green stripe. cut it. your speedo will still work and your ecu wont get a signal. after you do this yuou have to disconnect the 4th and 5th gear sensors on your tranny.
the othe rway i did was disconnecte fthe sensors and ran a toggle switch inline with my vehicle speed sensor. when i hit the swtich. it opens the signal and my speedo goes to 0. and the cars pulls.
__________________
RIP Tim. i miss you, buddy
RIP Tim. i miss you, buddy
Senior Member
Join Date: Jun 2000
Posts: 2,649
Likes: 0
Received 0 Likes
on
0 Posts
Originally posted by VortecFL
my car pulls all the way to 135 with no problem.. after that it take all of florida to reach 150's
my car pulls all the way to 135 with no problem.. after that it take all of florida to reach 150's
__________________
92' Nissan 240sx
02' Honda VFR Interceptor
08' Tundra
92' Nissan 240sx
02' Honda VFR Interceptor
08' Tundra
