anyone know about gauge cluster?
Guest
Posts: n/a
[QU073=1'm Phuck3d]y0u|2 clu573|2 15 d0|\|3 g37 4|\|07h3|2 0|\|3 4|\|d d0|\|'7 pull 7h3 |\|33dl35 0ff 0|2 1|\|574ll 1|\|d1gl0 g4ug35. 0|2 y0u c4|\| ju57 |23m3mb3|2 7h47 1/4 74|\|k 15 3mp7y 4|\|d d|21v3 0|\| \^/17h y0u|2 fub4|2 g4ug35.[/QU073]
D4v35 |21gh7, y0u 5c|23\^/3d y0u|253lf b|20
D4v35 |21gh7, y0u 5c|23\^/3d y0u|253lf b|20
Retired
Joined: Jan 2003
Posts: 5,095
Likes: 0
You weren't screwed before, but now you are. What you should have done when you ran out of gas was pulled the needle off and put it back on indicating E. I guess you could always run out of gas again and do it then...
__________________
realer than most
Joined: Sep 2003
Posts: 8,806
Likes: 0
Originally Posted by Epstein
You weren't screwed before, but now you are. What you should have done when you ran out of gas was pulled the needle off and put it back on indicating E. I guess you could always run out of gas again and do it then...
or fill up and put it on F....why in gods name did you take the needle off?
Retired
Joined: Jan 2003
Posts: 5,095
Likes: 0
Originally Posted by MrNiceGuy
or fill up and put it on F....why in gods name did you take the needle off?
You have to take the needles off when you install indiglo gauge faces.
__________________
do it BIG!!
Joined: Jul 2005
Posts: 1,340
Likes: 0
hahahaha....so superK..you took the needle off?
if ya left it factory...it should be relatively accurate..
remember..the fuel is sloshing back in forth in the tank..so the meter is gonna go up and down depending on if you're going uphill or downhill..
what i did..is..i fill up my tank..and i saw that the needle was maybe like...1mm off..
so i open up the clutster and push the needle...freely up..until there is some resistance..
then i just push it 1mm the point where it stopped moving freely
oh yeah...make sure your car is level...now put everything back in and turn the car on..the needle should move to FULL
im not sure about the fuel level sensor..
i heard somewhere that its a plastic container that floats somewhat like the balloon in the toilet resevoir...but over time..the plastic container would leak and fill w/ fuel and sink to the bottom..
if ya left it factory...it should be relatively accurate..
remember..the fuel is sloshing back in forth in the tank..so the meter is gonna go up and down depending on if you're going uphill or downhill..
what i did..is..i fill up my tank..and i saw that the needle was maybe like...1mm off..
so i open up the clutster and push the needle...freely up..until there is some resistance..
then i just push it 1mm the point where it stopped moving freely
oh yeah...make sure your car is level...now put everything back in and turn the car on..the needle should move to FULL
im not sure about the fuel level sensor..
i heard somewhere that its a plastic container that floats somewhat like the balloon in the toilet resevoir...but over time..the plastic container would leak and fill w/ fuel and sink to the bottom..
STANZZZZZZZZZZZZZZAAAAAAAAAAAHHH
Last edited by OniS14; Jan 10, 2006 at 06:42 AM.
Thread Starter
Banned
Joined: Apr 2005
Posts: 2,068
Likes: 0
ok im gonna try and fix it today hopefully i can fix the heat gauge as well? but i will post up when i get it done and im gonna try and fix my bumper so it look good and align my hood on.....
