Injectors wont fire on SR
shift.............vroooom
Thread Starter
Join Date: Feb 2004
Posts: 1,825
Likes: 0
Received 0 Likes
on
0 Posts
Injectors wont fire on SR
Hey guys, i need some help. The swap is done but the injectors wont fire. It has fuel pressure and spark but the injectors wont fire. I am thinking that this could be wiring, ecu, or maybe cam angle sensor not sending signal? I would appreciate some help....
All opinions are welcome.....
Thanx
Norlandt
All opinions are welcome.....
Thanx
Norlandt
__________________
http://inductionperformance.com/
Induction Performance - 727.505.1423
AEM EMS Tuning, Builds, Assembly, Custom Kits, Installs and more.....
http://inductionperformance.com/
Induction Performance - 727.505.1423
AEM EMS Tuning, Builds, Assembly, Custom Kits, Installs and more.....
Forever Broke Nissan
Join Date: Jan 2002
Posts: 6,860
Likes: 0
Received 0 Likes
on
0 Posts
are you spark plugs wet with fuel? if not check for continuity in your fuses and if that doesnt work pull out the injectors and spray it down with carb cleaner. may be clogged. if that doesnt work try and get your hands on a noid light test to see if you injectors are even getting a signal
__________________
If you have three quarters, four dimes, and four pennies, you have $1.19. You also have the largest amount of money in coins without being able to make change for a dollar.
If you have three quarters, four dimes, and four pennies, you have $1.19. You also have the largest amount of money in coins without being able to make change for a dollar.
Registered User
Join Date: Jun 2004
Posts: 153
Likes: 0
Received 0 Likes
on
0 Posts
The cam angle sensor is working... we have spark.. so that verifies that. The injectors aren't firing at all. I have a test light for the MSD injectors, and there's nothing there. I have verified the 12 volt feed going to them.. and double checked the grounds and resistors. All of that is in order.
Travis
Travis
__________________
www.fi-r.net
Nissan Performance
www.fi-r.net
Nissan Performance
Registered User
Join Date: Jun 2004
Posts: 153
Likes: 0
Received 0 Likes
on
0 Posts
I have the resistors on the negative (-) switched side of the circuit coming out of the ECU. I am using 6.8 ohm resistors.
Travis
Travis
__________________
www.fi-r.net
Nissan Performance
www.fi-r.net
Nissan Performance
shift.............vroooom
Thread Starter
Join Date: Feb 2004
Posts: 1,825
Likes: 0
Received 0 Likes
on
0 Posts
we are using an ecu programmed by enthalpy (scott).
__________________
http://inductionperformance.com/
Induction Performance - 727.505.1423
AEM EMS Tuning, Builds, Assembly, Custom Kits, Installs and more.....
http://inductionperformance.com/
Induction Performance - 727.505.1423
AEM EMS Tuning, Builds, Assembly, Custom Kits, Installs and more.....
shift.............vroooom
Thread Starter
Join Date: Feb 2004
Posts: 1,825
Likes: 0
Received 0 Likes
on
0 Posts
...this is so dumb man....im sick to my stomach with all the shit that happens to me...this kind of shit isnt fair. I just really pray to god that everything turns out good and the car runs fine because im on feet right now....I have faith in Travis and Scott so hopefully they can figure this out man......
Norlandt
Norlandt
__________________
http://inductionperformance.com/
Induction Performance - 727.505.1423
AEM EMS Tuning, Builds, Assembly, Custom Kits, Installs and more.....
http://inductionperformance.com/
Induction Performance - 727.505.1423
AEM EMS Tuning, Builds, Assembly, Custom Kits, Installs and more.....
Last edited by cubanprince1; 01-11-2005 at 04:19 PM.
