I need a parts llist
Boom Goes The Dynomite
Thread Starter
Join Date: Jul 2003
Posts: 1,699
Likes: 0
Received 0 Likes
on
0 Posts
I need a parts llist
I am gonna help goat with the 14b swap on his gsx he has the turbo. what else does he need. I have done the swap before but i cant remember what all is needed. Thanks
__________________
United States Air Force!
United States Air Force!
previously SLOWBOOST
Join Date: Jul 2004
Posts: 5,606
Likes: 0
Received 0 Likes
on
0 Posts
http://tampabay.dsm.org/phpBB/viewtopic.php?t=9480 this should help you out a bit.
__________________
FOR A WOUNDED MAN SHALL SAY TO HIS ASSAILANT
'IF I LIVE, I WILL KILL YOU. IF I DIE, YOU ARE FORGIVEN'
SUCH IS THE RULE OF HONOUR.
FOR A WOUNDED MAN SHALL SAY TO HIS ASSAILANT
'IF I LIVE, I WILL KILL YOU. IF I DIE, YOU ARE FORGIVEN'
SUCH IS THE RULE OF HONOUR.
Registered User
Join Date: Dec 2004
Posts: 796
Likes: 0
Received 0 Likes
on
0 Posts
i posted this before for him under his original thread, i was told this is what ya need. it sounds bout right to me
Parts needed:
14b
1g J-pipe
2g LICP
10" x 2" pipe (with beads welded at ends)
2g oil feed line (oil filter side)
1g oil feed line (turbo side)
1g or 2g drain pipe
1g or 2g water lines (bending needed)
Rubber fuel injection line
High-temp Copper/Silicone gasket maker
Total cost of install kit: $40
1. Cut the 2g LICP inbetween the two 90* bends
2. use 10" long pipe to raise LICP to the 1g J-pipe
3. cut 2g oil feed line near turbo
4. cut 1g oil feed line near the already cut 2g line
5. connect the two feed lines using fuel injection hose
6. install water lines, bend as needed
7. use gasket maker in place of mani->turbo, turbo->o2 housing, o2 housing->downpipe gaskets.
Parts needed:
14b
1g J-pipe
2g LICP
10" x 2" pipe (with beads welded at ends)
2g oil feed line (oil filter side)
1g oil feed line (turbo side)
1g or 2g drain pipe
1g or 2g water lines (bending needed)
Rubber fuel injection line
High-temp Copper/Silicone gasket maker
Total cost of install kit: $40
1. Cut the 2g LICP inbetween the two 90* bends
2. use 10" long pipe to raise LICP to the 1g J-pipe
3. cut 2g oil feed line near turbo
4. cut 1g oil feed line near the already cut 2g line
5. connect the two feed lines using fuel injection hose
6. install water lines, bend as needed
7. use gasket maker in place of mani->turbo, turbo->o2 housing, o2 housing->downpipe gaskets.
previously SLOWBOOST
Join Date: Jul 2004
Posts: 5,606
Likes: 0
Received 0 Likes
on
0 Posts
the second link within the link gets into the electrical shit.
__________________
FOR A WOUNDED MAN SHALL SAY TO HIS ASSAILANT
'IF I LIVE, I WILL KILL YOU. IF I DIE, YOU ARE FORGIVEN'
SUCH IS THE RULE OF HONOUR.
FOR A WOUNDED MAN SHALL SAY TO HIS ASSAILANT
'IF I LIVE, I WILL KILL YOU. IF I DIE, YOU ARE FORGIVEN'
SUCH IS THE RULE OF HONOUR.
Registered User
Join Date: Feb 2005
Posts: 17
Likes: 0
Received 0 Likes
on
0 Posts
hmm, all i did my swap with j pipe and both oil lines. thats it. i reused all my gaskets, but thats not good so go to mitsu and spend 20$ on gaskets. everything fit fine.
Registered User
Join Date: Feb 2005
Posts: 473
Likes: 0
Received 0 Likes
on
0 Posts
i have all the piping taken care of now. I don't really wanna splice the fuel injeciton lines in, unless thats gonna save me a good amount of $$.
aside from that, does anyone have any of the needed parts for sale?
aside from that, does anyone have any of the needed parts for sale?
