View Poll Results: which wheels to buy
weld prostar
5
55.56%
weld draglights
4
44.44%
Voters: 9. You may not vote on this poll
finally started the rebuild of the samurai
finally started the rebuild of the samurai
so is a 1986 Suzuki samurai with a 12a..... ok so i took over this project if you are going to critique the wheels please dont post i bought it with the wheels i dont know if i like them yet they are 20" wheels here is how i bought it:
So we started by taking out the eng to se what we were working with
after opening up the eng i dont even know how it was running you got to love a 12a
the rotors and housing are no good not even the 3mm apex seals can fix them so if anyone know where i could get a hold of 1 12a housing and the rotors hit me up. i recived all the parts for the sami but there is still much work
this harnest is worth less i bought one from ez wiring
almost all cleaned up getting it ready fro paint
the i removed the dash and all the wires
i am replacing it with an all aluminum one just like this one
this is the set up im going with:
12a half BP all seals replased with atkins (apex, side, and solid corner, 93 corner spring) replacing everything with new
stage 1 exedy clutch
with a holley 600
holley blue fuel pump
all new electronic gauges (found a place that would custom make the speedo sending unit)
the samurai had the rear end replaced with a dana 44 so i bought 4.55 ring and pinion with all new install kit
i will keep up dating the pictures
new pics 99% done
So we started by taking out the eng to se what we were working with
after opening up the eng i dont even know how it was running you got to love a 12a
the rotors and housing are no good not even the 3mm apex seals can fix them so if anyone know where i could get a hold of 1 12a housing and the rotors hit me up. i recived all the parts for the sami but there is still much work
this harnest is worth less i bought one from ez wiring
almost all cleaned up getting it ready fro paint
the i removed the dash and all the wires
i am replacing it with an all aluminum one just like this one
this is the set up im going with:
12a half BP all seals replased with atkins (apex, side, and solid corner, 93 corner spring) replacing everything with new
stage 1 exedy clutch
with a holley 600
holley blue fuel pump
all new electronic gauges (found a place that would custom make the speedo sending unit)
the samurai had the rear end replaced with a dana 44 so i bought 4.55 ring and pinion with all new install kit
i will keep up dating the pictures
new pics 99% done
__________________
R.A.P.S member number #0006
Rotaries
Against
Piston
Swaps
msn: prican8069
yahoo: ltorovelez
aim: ltorovelez
R.A.P.S member number #0006
Rotaries
Against
Piston
Swaps
msn: prican8069
yahoo: ltorovelez
aim: ltorovelez
Last edited by prican; 08-15-2010 at 04:03 PM. Reason: new pictures
if its done by the which it should be sure
__________________
R.A.P.S member number #0006
Rotaries
Against
Piston
Swaps
msn: prican8069
yahoo: ltorovelez
aim: ltorovelez
R.A.P.S member number #0006
Rotaries
Against
Piston
Swaps
msn: prican8069
yahoo: ltorovelez
aim: ltorovelez
Good luck with your build
__________________
My FD
http://www.sfldrifters.com/forums/sh...ad.php?t=52081
http://www.rx7club.com/showthread.php?t=836503
My FD
http://www.sfldrifters.com/forums/sh...ad.php?t=52081
http://www.rx7club.com/showthread.php?t=836503
today felt like christmas i got all my parts but the gauges which should be here tomorrow
the dash
MSD coils
racing beat mani
speed sensor to switch from mechanical to electronic speedo
holley 1850-2
i also received the shipment from Atkins but every thing is wrapped and i dont want to open them till I'm ready to use parts i also received the holley blue fuel pump. i will be picking up the housing and rotor that i need tomorrow. I'm looking for someone to paint the engine compartment hood and dash for a fair price let me know if any of you know someone.
the dash
MSD coils
racing beat mani
speed sensor to switch from mechanical to electronic speedo
holley 1850-2
i also received the shipment from Atkins but every thing is wrapped and i dont want to open them till I'm ready to use parts i also received the holley blue fuel pump. i will be picking up the housing and rotor that i need tomorrow. I'm looking for someone to paint the engine compartment hood and dash for a fair price let me know if any of you know someone.
__________________
R.A.P.S member number #0006
Rotaries
Against
Piston
Swaps
msn: prican8069
yahoo: ltorovelez
aim: ltorovelez
R.A.P.S member number #0006
Rotaries
Against
Piston
Swaps
msn: prican8069
yahoo: ltorovelez
aim: ltorovelez
so i have a dilemma i found both of the wheels i like the weld draglights or the weld prostar i will post a poll to see which one you guys think would look the best
__________________
R.A.P.S member number #0006
Rotaries
Against
Piston
Swaps
msn: prican8069
yahoo: ltorovelez
aim: ltorovelez
R.A.P.S member number #0006
Rotaries
Against
Piston
Swaps
msn: prican8069
yahoo: ltorovelez
aim: ltorovelez
Nice progress. Keep us updated.
__________________
My FD
http://www.sfldrifters.com/forums/sh...ad.php?t=52081
http://www.rx7club.com/showthread.php?t=836503
My FD
http://www.sfldrifters.com/forums/sh...ad.php?t=52081
http://www.rx7club.com/showthread.php?t=836503