car pics
Thread Starter
80cubic inch powerhouse
Joined: Feb 2003
Posts: 70
Likes: 0
Hey, thank you all very much for all the props. and to answer some questions: i usually only run like 15 psi on the street. the dyno sheet with the 450rwhp was on 14psi untuned with mild timing. i havent been back to the dyno yet so im not really wanting to go crazy right now as far as street boost. i see full boost at about 4500 give or take a bit. because i mainly do nothing else but drag i went for alot of hp. so this turbo starts coming alive at about 19 psi. i reccomend that if you are going with a big turbo to have it Q trimmed for good responsive spool. as well as a good manifold setup. i stand by the hks stainless, as well as well made tubular equal length manifolds. the car has been cleaned up alot since that pic and i will post some more as well as pics from sevenstock when i get back. oh and max boost for the street is limited especially with this 91 octane bullshit i have to deal with here. but i will soon be doing water injection and run 20psi on the street on the weekends.
__________________
AIM NAME: TEKNO192
AIM NAME: TEKNO192
SOLAR-SPECIALIST.COM
Joined: Dec 2002
Posts: 5,424
Likes: 0
Originally posted by 1BAD7
hey ride or die tell me your mods and i can give you a good idea of what turbo will work very well. have you looked into a gtq67?
hey ride or die tell me your mods and i can give you a good idea of what turbo will work very well. have you looked into a gtq67?
Well right now I have a brand new (420 miles) large streetported engine, Greddy fmic, 4x720cc inj., walbrol pump, mallory fpr, s-afc (soon to be replaced with MT LT-
, Greddy profec B, full 3" turbback SS exhaust no cat, t04b hybrid turbo. I am about to go with the LT-8 and then I think this turbo right here:http://store.yahoo.com/cheapturbo/garrettto4r.html
I'll probably just go with the HKS standard cast mani for a while and either a tial or HKS WG. And for fuel I'll be adding 2x1600cc secondaries.
Thread Starter
80cubic inch powerhouse
Joined: Feb 2003
Posts: 70
Likes: 0
who ported your motor for you? what kind of power r you looking to make? i have the turbonetics newgen wastegate which i highly reccomend. but the tial is also another good one. i have never really had any dealings with hks gates. that turbo is good. it will spool well and decently fast for its size but like i said just make sure you get it q trimmed.
__________________
AIM NAME: TEKNO192
AIM NAME: TEKNO192
SOLAR-SPECIALIST.COM
Joined: Dec 2002
Posts: 5,424
Likes: 0
Originally posted by 1BAD7
who ported your motor for you? what kind of power r you looking to make? i have the turbonetics newgen wastegate which i highly reccomend. but the tial is also another good one. i have never really had any dealings with hks gates. that turbo is good. it will spool well and decently fast for its size but like i said just make sure you get it q trimmed.
who ported your motor for you? what kind of power r you looking to make? i have the turbonetics newgen wastegate which i highly reccomend. but the tial is also another good one. i have never really had any dealings with hks gates. that turbo is good. it will spool well and decently fast for its size but like i said just make sure you get it q trimmed.
A guy named Sam built and ported my engine. I'd like to make at least 400rwhp @ 14psi and hopefully around 425-450 @ 20psi.
