Will i have to switch hubs
rex90sir2
Thread Starter
Join Date: Jan 2008
Posts: 120
Likes: 0
Received 0 Likes
on
0 Posts
Will i have to switch hubs
i have a 90 crx hf im putting a jdmd15b with a 89 crx si tranny in it will i need to change the hubs heard that hf's are smaller if so i have a set of complete arms with disk caliper and bearings from my 89crx si will these work???
also whats the model numer for the 89 si cable tranny?
thanks
also whats the model numer for the 89 si cable tranny?
thanks
engine building &best
Join Date: May 2003
Posts: 11,971
Likes: 0
Received 0 Likes
on
0 Posts
yes u need to swp them..just go to the junk yard any Dx crx/civic will work to..
__________________
i love AUTOZONE
MY CAR iS PROTECTED BY ZOOMBAK GPS LOCATOR IS YOURS?
175+served in engines built from minime to gsr/lsvtec,b16 b20vtec,d15 k24 powerhouses or just rebuilds.life is good
i like when people don't take my advice.cause then i make more money when u need it rebuild the right way!
how many speed holes do i need in my bumper,b4 i can run 15's?
i love AUTOZONE
MY CAR iS PROTECTED BY ZOOMBAK GPS LOCATOR IS YOURS?
175+served in engines built from minime to gsr/lsvtec,b16 b20vtec,d15 k24 powerhouses or just rebuilds.life is good
i like when people don't take my advice.cause then i make more money when u need it rebuild the right way!
how many speed holes do i need in my bumper,b4 i can run 15's?
Found the Vtec switch.
Join Date: Jun 2007
Posts: 2,296
Likes: 0
Received 0 Likes
on
0 Posts
Actually you dont. Only the outer hub is smaller, the inner hub will go into the si tranny just fine. Its when you want to upgrade to bigger brakes or go B series (which had no small hub model) that you need to swap them.
__________________
TR Old Skool EF Crew #24
TR Old Skool EF Crew #24
engine building &best
Join Date: May 2003
Posts: 11,971
Likes: 0
Received 0 Likes
on
0 Posts
It's cheaper to just replace the whole knuckel then rebuild a axle safely for this application tho.
__________________
i love AUTOZONE
MY CAR iS PROTECTED BY ZOOMBAK GPS LOCATOR IS YOURS?
175+served in engines built from minime to gsr/lsvtec,b16 b20vtec,d15 k24 powerhouses or just rebuilds.life is good
i like when people don't take my advice.cause then i make more money when u need it rebuild the right way!
how many speed holes do i need in my bumper,b4 i can run 15's?
i love AUTOZONE
MY CAR iS PROTECTED BY ZOOMBAK GPS LOCATOR IS YOURS?
175+served in engines built from minime to gsr/lsvtec,b16 b20vtec,d15 k24 powerhouses or just rebuilds.life is good
i like when people don't take my advice.cause then i make more money when u need it rebuild the right way!
how many speed holes do i need in my bumper,b4 i can run 15's?
Found the Vtec switch.
Join Date: Jun 2007
Posts: 2,296
Likes: 0
Received 0 Likes
on
0 Posts
if by arm you mean the steering knuckle, then yes you could but make sure youve got axles to match or your going to be sitting there with you thumb up your ass..lol
The actual suspension arms are the same, you just swap one knuckle for the other.
The actual suspension arms are the same, you just swap one knuckle for the other.
__________________
TR Old Skool EF Crew #24
TR Old Skool EF Crew #24
rex90sir2
Thread Starter
Join Date: Jan 2008
Posts: 120
Likes: 0
Received 0 Likes
on
0 Posts
ok thanks im using and si tranny and im going to get si axles
Once Ruled The World .l..
Join Date: Dec 1998
Posts: 3,993
Likes: 0
Received 0 Likes
on
0 Posts
If your using an Si Tranny, then you need axles & Hubs (knuckles)...
88-91 SI, LX, EX DX knuckles & Axles will work...
It's not about horse power, it's about spline count..
88-91 SI, LX, EX DX knuckles & Axles will work...
It's not about horse power, it's about spline count..
__________________
TR"Old Skool EF & DA Crews" Member #46
TR "Wagovan Club" Member #1
TR"Old Skool EF & DA Crews" Member #46
TR "Wagovan Club" Member #1
