whici pins for ctr pistons on ls rods?

Reply Subscribe

Thread Tools

May 10, 2005 | 05:04 PM

#1 (permalink)

freakasis

Thread Starter

Registered User

Joined: May 2004

Posts: 3,478

Likes: 0

which pins for ctr pistons on ls rods?

which wrist pins are long enough to fit the ctr pistons? they cant look up the ctrs at the dealership. i can get itr gsr ls b16....which ones will work best?

Last edited by freakasis; May 10, 2005 at 05:13 PM.

May 10, 2005 | 07:21 PM

#2 (permalink)

1fasthatch

Traction Problems

Joined: Jul 2003

Posts: 662

Likes: 0

I'm pretty sure any OEM B series piston wrist pin will work!!!

__________________
www.artofspeedproductions.com

May 10, 2005 | 07:31 PM

#3 (permalink)

freakasis

Thread Starter

Registered User

Joined: May 2004

Posts: 3,478

Likes: 0

i thaught so too but the Ls ones that i have just seem too short.

May 10, 2005 | 07:37 PM

#4 (permalink)

1fasthatch

Traction Problems

Joined: Jul 2003

Posts: 662

Likes: 0

the only thing you need to do is have the rods machined

If I'm worng someone correct me

__________________
www.artofspeedproductions.com

May 10, 2005 | 08:19 PM

#5 (permalink)

freakasis

Thread Starter

Registered User

Joined: May 2004

Posts: 3,478

Likes: 0

i know i need to have the rods machined, i just thaught the pins looked a bit too short.

May 11, 2005 | 12:13 AM

#6 (permalink)

rangcrx

engine building &amp;amp;best

Joined: May 2003

Posts: 11,971

Likes: 0

all the pins are the same thay only look longer in the pistons cause the way typeRs are cut thay will all work the same if your use ctr i would say go with the cromoly thay are lighter and will last and are perfect you need part 10426 http://probeindustries.com/Wrist_Pin...=Chromoly+Race

__________________
i love AUTOZONE
MY CAR iS PROTECTED BY ZOOMBAK GPS LOCATOR IS YOURS?

175+served in engines built from minime to gsr/lsvtec,b16 b20vtec,d15 k24 powerhouses or just rebuilds.life is good
i like when people don't take my advice.cause then i make more money when u need it rebuild the right way!

how many speed holes do i need in my bumper,b4 i can run 15's?

May 11, 2005 | 11:46 AM

#7 (permalink)

freakasis

Thread Starter

Registered User

Joined: May 2004

Posts: 3,478

Likes: 0

ok thanks

May 11, 2005 | 01:13 PM

#8 (permalink)

mtber

Registered User

Joined: Jan 2003

Posts: 5,450

Likes: 0

Do not machine the rods. Mill the piston 1mm on each side so that the ls rod fits in the piston. Make sure to balance the pistons.

__________________

Authorized Dealer & Tuner for: Hondata, eCtune, Neptune, AEM, Crome, Precision Turbo, Omni Power, Walbro, Innovate & more. Dyno Tuning Services, Ecu Chipping, Chipped Ecus, Conversion Harnesses, Widebands, Fuel Injectors, Fuel Pumps, Map Sensors & more.
For more information visit http://www.Phearable.net or call 1-888-236-9831