Best Place to Get Bushings Pressed?
Thread Starter
TR Balla Donor Supreme
Joined: Aug 2001
Posts: 2,923
Likes: 0
Best Place to Get Bushings Pressed?
im finally swapping over a gs-r suspension to my dx and i figured while im at it i should swap out the stock bushings for some ES ones. anyone know any place good locally?
Engineer at the source
Joined: Jun 2003
Posts: 2,722
Likes: 0
engine building &best
Joined: May 2003
Posts: 11,971
Likes: 0
do it yourself with c-clamps
__________________
i love AUTOZONE
MY CAR iS PROTECTED BY ZOOMBAK GPS LOCATOR IS YOURS?
175+served in engines built from minime to gsr/lsvtec,b16 b20vtec,d15 k24 powerhouses or just rebuilds.life is good
i like when people don't take my advice.cause then i make more money when u need it rebuild the right way!
how many speed holes do i need in my bumper,b4 i can run 15's?
i love AUTOZONE
MY CAR iS PROTECTED BY ZOOMBAK GPS LOCATOR IS YOURS?
175+served in engines built from minime to gsr/lsvtec,b16 b20vtec,d15 k24 powerhouses or just rebuilds.life is good
i like when people don't take my advice.cause then i make more money when u need it rebuild the right way!
how many speed holes do i need in my bumper,b4 i can run 15's?
engine building &amp;amp;best
Joined: May 2003
Posts: 11,971
Likes: 0
i did my hole 89 hatchback with 5 cClamps but i also had a hugh one for the rear trailer arm ..just lube them up i think the rear arm is the harddest
__________________
i love AUTOZONE
MY CAR iS PROTECTED BY ZOOMBAK GPS LOCATOR IS YOURS?
175+served in engines built from minime to gsr/lsvtec,b16 b20vtec,d15 k24 powerhouses or just rebuilds.life is good
i like when people don't take my advice.cause then i make more money when u need it rebuild the right way!
how many speed holes do i need in my bumper,b4 i can run 15's?
i love AUTOZONE
MY CAR iS PROTECTED BY ZOOMBAK GPS LOCATOR IS YOURS?
175+served in engines built from minime to gsr/lsvtec,b16 b20vtec,d15 k24 powerhouses or just rebuilds.life is good
i like when people don't take my advice.cause then i make more money when u need it rebuild the right way!
how many speed holes do i need in my bumper,b4 i can run 15's?
Its a secret
Joined: Oct 2003
Posts: 1,764
Likes: 0
ok i neeed to do this too
some one explain about the c clamp how do it do it
some one explain about the c clamp how do it do it
__________________
The Myspace Page
Hero's arent born there american
made.
Aco. 53rd CSB LTF - TMT - 1st SQD
Afganistan Tour 2005 - 2006
- Its Game Time -
The Myspace Page
Hero's arent born there american
made.
Aco. 53rd CSB LTF - TMT - 1st SQD
Afganistan Tour 2005 - 2006
- Its Game Time -
engine building &amp;amp;best
Joined: May 2003
Posts: 11,971
Likes: 0
where you located if your close i will help you out or show you cause you need more then just the clamp you need a roll of tape or small pipe
__________________
i love AUTOZONE
MY CAR iS PROTECTED BY ZOOMBAK GPS LOCATOR IS YOURS?
175+served in engines built from minime to gsr/lsvtec,b16 b20vtec,d15 k24 powerhouses or just rebuilds.life is good
i like when people don't take my advice.cause then i make more money when u need it rebuild the right way!
how many speed holes do i need in my bumper,b4 i can run 15's?
i love AUTOZONE
MY CAR iS PROTECTED BY ZOOMBAK GPS LOCATOR IS YOURS?
175+served in engines built from minime to gsr/lsvtec,b16 b20vtec,d15 k24 powerhouses or just rebuilds.life is good
i like when people don't take my advice.cause then i make more money when u need it rebuild the right way!
how many speed holes do i need in my bumper,b4 i can run 15's?
