today I was not scarred to open the door..pics
Thread Starter
Chucking up the Dueces
Joined: Jun 2002
Posts: 8,370
Likes: 1
today I was not scarred to open the door..pics
Well I guess we get sat del,when I came home I saw two boxes by the door.
__________________
Caputo Motorsports-Shawn Caputo
Induction Performance.com
PTC torque converter
Aerospace Components
ProFab Performance
R.I automotive
C.R.T transmisions
5.13@145mph
Caputo Motorsports-Shawn Caputo
Induction Performance.com
PTC torque converter
Aerospace Components
ProFab Performance
R.I automotive
C.R.T transmisions
5.13@145mph
Last edited by cochese; Aug 31, 2006 at 03:11 PM.
Thread Starter
Chucking up the Dueces
Joined: Jun 2002
Posts: 8,370
Likes: 1
No back because of the backspace issue,I'm going to call them monday to see if the will make me a wheel.They only offer a 15x10 with a 6 inch back space,I'm going to see if I can get a 6.5
__________________
Caputo Motorsports-Shawn Caputo
Induction Performance.com
PTC torque converter
Aerospace Components
ProFab Performance
R.I automotive
C.R.T transmisions
5.13@145mph
Caputo Motorsports-Shawn Caputo
Induction Performance.com
PTC torque converter
Aerospace Components
ProFab Performance
R.I automotive
C.R.T transmisions
5.13@145mph
Guest
Posts: n/a
Good luck, but I doubt they will make the custom. The Alumastar rears are a 3 peice wheel, and they just take a standard center and standard hoop sections to come up with something. Then again, I could be wrong...
You could just go with the 6 and get the rear narrowed a touch if it needs it. I know the place up here gets 90 to cut, narrow and weld the housing, and if you have aftermarket axles with C clip elims there is usually enough spline to cut an inch or two off and still have plenty left. Hell, if you do that you could actually get a few inches lopped off, and be one of the few that can run with a deep dish wheel.
You could just go with the 6 and get the rear narrowed a touch if it needs it. I know the place up here gets 90 to cut, narrow and weld the housing, and if you have aftermarket axles with C clip elims there is usually enough spline to cut an inch or two off and still have plenty left. Hell, if you do that you could actually get a few inches lopped off, and be one of the few that can run with a deep dish wheel.
Thread Starter
Chucking up the Dueces
Joined: Jun 2002
Posts: 8,370
Likes: 1
Good luck, but I doubt they will make the custom. The Alumastar rears are a 3 peice wheel, and they just take a standard center and standard hoop sections to come up with something. Then again, I could be wrong...
You could just go with the 6 and get the rear narrowed a touch if it needs it. I know the place up here gets 90 to cut, narrow and weld the housing, and if you have aftermarket axles with C clip elims there is usually enough spline to cut an inch or two off and still have plenty left. Hell, if you do that you could actually get a few inches lopped off, and be one of the few that can run with a deep dish wheel.
You could just go with the 6 and get the rear narrowed a touch if it needs it. I know the place up here gets 90 to cut, narrow and weld the housing, and if you have aftermarket axles with C clip elims there is usually enough spline to cut an inch or two off and still have plenty left. Hell, if you do that you could actually get a few inches lopped off, and be one of the few that can run with a deep dish wheel.
__________________
Caputo Motorsports-Shawn Caputo
Induction Performance.com
PTC torque converter
Aerospace Components
ProFab Performance
R.I automotive
C.R.T transmisions
5.13@145mph
Caputo Motorsports-Shawn Caputo
Induction Performance.com
PTC torque converter
Aerospace Components
ProFab Performance
R.I automotive
C.R.T transmisions
5.13@145mph
Flowmaster nut swinger
Joined: Jan 2005
Posts: 7,535
Likes: 0
You could just go with the 6 and get the rear narrowed a touch if it needs it. I know the place up here gets 90 to cut, narrow and weld the housing, and if you have aftermarket axles with C clip elims there is usually enough spline to cut an inch or two off and still have plenty left. Hell, if you do that you could actually get a few inches lopped off, and be one of the few that can run with a deep dish wheel.
Hey Adam there is also A.R.T. down here in clearwater they did the same thing for my rear a couple years back. came out great.
__________________
All American Street Car Performance <--- Facebook page link, check us out!
6187 126th Ave North
Largo fl 33773
MV#72427
(727)535-6905 - Shaun
All American Street Car Performance <--- Facebook page link, check us out!
6187 126th Ave North
Largo fl 33773
MV#72427
(727)535-6905 - Shaun
