AgentAndys 1uz-fe swap FS 240sx plug and play
Thread Starter
more class than college
Joined: Jul 2003
Posts: 859
Likes: 0
AgentAndys 1uz-fe swap FS 240sx plug and play
1UZ-FE COMPLETE 240SX SWAP FS!!
R154 transmission XAT billet adapter, shifter and extension
cusco hyper single clutch with push pull conversion
aluminum driveshaft
engine and trans mounts
headers, mid pipes, carbon ti/ catback
full wiring harness ready to install
power steering lines
aluminum radiator with hoses and FLX220 fans
heater hoses
clutch slave and stainless braided line
Intake with blitz SUS stainless filter and 4 1/2" intake with MAF sensor
Asking 5000. This is a complete swap and can be done in a few hours and you can have a very rare and fun to drive swap. This engine is in great shape with new valve cover gaskets, new waterpump, timing belt, belt bearings, DENSO iridium plugs($85!!), perfect condition wires, and some new harness plugs to ensure that it all stays together. I have been driving on this swap for over 6 months now after developing it and cannot be happier with the results. Motor pulls real strong at any rpm, you simply cannot beat this setup. The clutch is a Cusco hyper single and the transmission is the durable supra turbo 5 speed. I made all the mounts and harness and completly stand behind the workmanship of this swap. I am selling this to fund the next version of this V8 saga. I am building a full built high rev NA 3UZ, so in no way am i running away from what I am selling, only trying to get deeper.
I will consider offers but lets think about the pure cost of everything and the fact all these parts are custom made and not off the shelf(unless your looking at XATRACING.COM)
I will install for 800 dollars if the buyer wants.
SALES@XATRACING.COM
941-306-8270
R154 transmission XAT billet adapter, shifter and extension
cusco hyper single clutch with push pull conversion
aluminum driveshaft
engine and trans mounts
headers, mid pipes, carbon ti/ catback
full wiring harness ready to install
power steering lines
aluminum radiator with hoses and FLX220 fans
heater hoses
clutch slave and stainless braided line
Intake with blitz SUS stainless filter and 4 1/2" intake with MAF sensor
Asking 5000. This is a complete swap and can be done in a few hours and you can have a very rare and fun to drive swap. This engine is in great shape with new valve cover gaskets, new waterpump, timing belt, belt bearings, DENSO iridium plugs($85!!), perfect condition wires, and some new harness plugs to ensure that it all stays together. I have been driving on this swap for over 6 months now after developing it and cannot be happier with the results. Motor pulls real strong at any rpm, you simply cannot beat this setup. The clutch is a Cusco hyper single and the transmission is the durable supra turbo 5 speed. I made all the mounts and harness and completly stand behind the workmanship of this swap. I am selling this to fund the next version of this V8 saga. I am building a full built high rev NA 3UZ, so in no way am i running away from what I am selling, only trying to get deeper.
I will consider offers but lets think about the pure cost of everything and the fact all these parts are custom made and not off the shelf(unless your looking at XATRACING.COM)
I will install for 800 dollars if the buyer wants.
SALES@XATRACING.COM
941-306-8270
__________________
------------------------------------------------
Andrew Carroll @ XAT RACING
team v8 in the works. hold one tango.....
hot hot heat in the cup!!!
------------------------------------------------
Andrew Carroll @ XAT RACING
team v8 in the works. hold one tango.....
hot hot heat in the cup!!!
Registered User
Joined: Jul 2008
Posts: 1,829
Likes: 0
From the pic I take it this is for a s13...? So change the driveshaft and wire harness and it could be for s14? Also it looks like you got rid of the mess of stuff you dont need from the intake mani.
Thread Starter
more class than college
Joined: Jul 2003
Posts: 859
Likes: 0
correct on 13 to 14. easy conversion, i will do the wiring for free and I assume the shaft could be modded for 100-200
__________________
------------------------------------------------
Andrew Carroll @ XAT RACING
team v8 in the works. hold one tango.....
hot hot heat in the cup!!!
------------------------------------------------
Andrew Carroll @ XAT RACING
team v8 in the works. hold one tango.....
hot hot heat in the cup!!!
Thread Starter
more class than college
Joined: Jul 2003
Posts: 859
Likes: 0
willing to talk OBO on this as i really want to start the V2.
__________________
------------------------------------------------
Andrew Carroll @ XAT RACING
team v8 in the works. hold one tango.....
hot hot heat in the cup!!!
------------------------------------------------
Andrew Carroll @ XAT RACING
team v8 in the works. hold one tango.....
hot hot heat in the cup!!!
February - Ride of the Month
Joined: Apr 2005
Posts: 7,141
Likes: 0
Thread Starter
more class than college
Joined: Jul 2003
Posts: 859
Likes: 0
Sold......to.....
__________________
------------------------------------------------
Andrew Carroll @ XAT RACING
team v8 in the works. hold one tango.....
hot hot heat in the cup!!!
------------------------------------------------
Andrew Carroll @ XAT RACING
team v8 in the works. hold one tango.....
hot hot heat in the cup!!!
February - Ride of the Month
Joined: Apr 2005
Posts: 7,141
Likes: 0
