F/S 1999 civic hatch “SI” TURBO with AC
Thread Starter
Registered User
Joined: Jun 2007
Posts: 131
Likes: 0
F/S 1999 civic hatch “SI” TURBO with AC
9 <a bord
-
ice cold A/C
-
rbon f
1999 civic hatch “SI” TURBO
-very fresh paint not a ding or dent “flawless” 1200
-CLEAN CARFAX
- ice cold A/C
-si front lip urethane/ type R rear lip 150
-type R black head lights/ tail lights 100
-8k HID headlights 100
-carbon fiber grill
-integra front seats interior is flawless as well 80
-tokico blue struts 270
-neuspeed springs 200
- lakewood adjustable traction bars 350
-skunk 2 camber kit front and rear 200
- MINT bronze Rota C10 16s with hoosier drags
-01 integra front spindles and rear trailing arms (upgrades 9in to 10in rotors and rear drum to di
400+
-New rear hub bearing 200
-Crossed drilled slotted rotors 90
-Ceramic pads 60
-Strut tower bars front and rear 80
-aem tru boost gauge/controller settings off (10psi) A(15psi)B(24psi) 300
-aem water/meth injection kit 300
-aem wide band 219
-autometer oil pressure gauge 50
-walbro 255 fuel pump 100
-precision 780cc injectors 280
-gm 3 bar map sensor 75
-conversion harness obd2 to obd1 75
-oem oil pump 130
-new oem distributor (distributor king) 130
-oem water pump 40
-aluminum radiator with FAL fan 300
-oem Honda green rod bearings 128
-oem Honda main bearing 90
-oem Honda timing belt and tensioner 65
-oem rear main seal 22
-oem gaskets and o-rings
-block machined 3 thousanths over stock and decked 300
-block guard 100
-noched for rod clearance
-skunk 2 cam gear 40
-eagle rods 320
-arp rod bolt arp head studs 155
-vitara pistons 190
-ported and polished and gasket matched head w/ 5 angle valve job flow jetted (flows equivalent to b16 head) 500+
-skunk 2 intake ported and polished and gasket matched 225+
-hondata intake manifold gasket 45
- omni power throttle body 200
-custom topmount turbo manifold 500+ A/C compatible
-3in down pipe to stock exhaust with electronic cut out 200+
-true 2.5 in. charge piping 190
- front mount intercooler 150
-tial waste gate 38mm 190
-tial blowoff 38mm 190
-lsd dragger clutch 6 puck sprung 500
-resurfaced fly wheel 45
- custom tig welded aluminum positive crank case ventilation 100
-synchro tech si transmission gearspeed carbon synchros/ Mfactory L.S.D 1500
-skunt 2 short shifter and weighted shift knob
-urethane filled motor mounts
-the most important part the tune!!! 600+
-Lots of parts…this is a complete build that makes over 340wheel horse power and 250ft/lbs of torque (HAVE ALL DYNO SLIPS)still not enough well do your research on how much power this build can make add race gas tune get another 40+hp want more put a cam valve spring and retainers In and kill the dyno with over 400 hp!!!! Safely!!! you don’t need to do this for more power literally you can just kick up the boost… but if you appreciate how I built the car you should make safe reliable power by using upgrades. this car is my daily driven car and literally if you just change the plugs and oil and run 93 octane gas it will last you a lifetime I promise you!! Well as long as none of your dipshit friends drives it and really doesn’t know how to drive! this car is fast and handles amazingly it stops on a dime and will put you in your seat I am selling it because I’m not driving as often and it’s my secondary vehicle so no I’m not going to be in a rush to get rid off it so I wont except low balls. I love this car and have built it myself and I will tell you everything
So if you do the math I spent over $12,500 on parts plus the 4,000 I spent on the car. by the way I have pics receipts and a carfax for the car when I bought it. With the labor and parts i put into it its my loss and somebody elses gain
asking price: $10,000
contact info: -aaron-
727-542-1072
call or text anytime
- ice cold A/C -rbon f1999 civic hatch “SI” TURBO
-very fresh paint not a ding or dent “flawless” 1200
-CLEAN CARFAX
- ice cold A/C
-si front lip urethane/ type R rear lip 150
-type R black head lights/ tail lights 100
-8k HID headlights 100
-carbon fiber grill
-integra front seats interior is flawless as well 80
-tokico blue struts 270
-neuspeed springs 200
- lakewood adjustable traction bars 350
-skunk 2 camber kit front and rear 200
- MINT bronze Rota C10 16s with hoosier drags
-01 integra front spindles and rear trailing arms (upgrades 9in to 10in rotors and rear drum to di
400+-New rear hub bearing 200
-Crossed drilled slotted rotors 90
-Ceramic pads 60
-Strut tower bars front and rear 80
-aem tru boost gauge/controller settings off (10psi) A(15psi)B(24psi) 300
-aem water/meth injection kit 300
-aem wide band 219
-autometer oil pressure gauge 50
-walbro 255 fuel pump 100
-precision 780cc injectors 280
-gm 3 bar map sensor 75
-conversion harness obd2 to obd1 75
-oem oil pump 130
-new oem distributor (distributor king) 130
-oem water pump 40
-aluminum radiator with FAL fan 300
-oem Honda green rod bearings 128
-oem Honda main bearing 90
-oem Honda timing belt and tensioner 65
-oem rear main seal 22
-oem gaskets and o-rings
-block machined 3 thousanths over stock and decked 300
-block guard 100
-noched for rod clearance
-skunk 2 cam gear 40
-eagle rods 320
-arp rod bolt arp head studs 155
-vitara pistons 190
-ported and polished and gasket matched head w/ 5 angle valve job flow jetted (flows equivalent to b16 head) 500+
-skunk 2 intake ported and polished and gasket matched 225+
-hondata intake manifold gasket 45
- omni power throttle body 200
-custom topmount turbo manifold 500+ A/C compatible
-3in down pipe to stock exhaust with electronic cut out 200+
-true 2.5 in. charge piping 190
- front mount intercooler 150
-tial waste gate 38mm 190
-tial blowoff 38mm 190
-lsd dragger clutch 6 puck sprung 500
-resurfaced fly wheel 45
- custom tig welded aluminum positive crank case ventilation 100
-synchro tech si transmission gearspeed carbon synchros/ Mfactory L.S.D 1500
-skunt 2 short shifter and weighted shift knob
-urethane filled motor mounts
-the most important part the tune!!! 600+
-Lots of parts…this is a complete build that makes over 340wheel horse power and 250ft/lbs of torque (HAVE ALL DYNO SLIPS)still not enough well do your research on how much power this build can make add race gas tune get another 40+hp want more put a cam valve spring and retainers In and kill the dyno with over 400 hp!!!! Safely!!! you don’t need to do this for more power literally you can just kick up the boost… but if you appreciate how I built the car you should make safe reliable power by using upgrades. this car is my daily driven car and literally if you just change the plugs and oil and run 93 octane gas it will last you a lifetime I promise you!! Well as long as none of your dipshit friends drives it and really doesn’t know how to drive! this car is fast and handles amazingly it stops on a dime and will put you in your seat I am selling it because I’m not driving as often and it’s my secondary vehicle so no I’m not going to be in a rush to get rid off it so I wont except low balls. I love this car and have built it myself and I will tell you everything
So if you do the math I spent over $12,500 on parts plus the 4,000 I spent on the car. by the way I have pics receipts and a carfax for the car when I bought it. With the labor and parts i put into it its my loss and somebody elses gain
asking price: $10,000
contact info: -aaron-
727-542-1072
call or text anytime
Last edited by aaron's sct; Jul 31, 2011 at 03:10 PM.
I Give My .02 When Needed
Joined: Mar 2009
Posts: 4,328
Likes: 0
Normally I would say that $10,000 is A LOT to ask for a single cam....but this is mint as hell. Looks like a badass ride! Bump for you
__________________
Nikon Owner
IG: @equippedphotography
FB: Equipped Photography1994 Integra RS - Stock LS/SOLD
1994 Del Sol - Stock D16y8/TRADED
1990 CRX Si - SiR B16a/TRADED
1998 Integra GS - JDM B20b/TRADED
1994 Integra GSR - Tuned H22a/TRADED
1999 EK Coupe - Backburner
1995 JDM Front Integra - Project
2014 F-150 5.0L - DD
Nikon Owner
IG: @equippedphotography
FB: Equipped Photography
1994 Del Sol - Stock D16y8/TRADED
1990 CRX Si - SiR B16a/TRADED
1998 Integra GS - JDM B20b/TRADED
1994 Integra GSR - Tuned H22a/TRADED
1999 EK Coupe - Backburner
1995 JDM Front Integra - Project
2014 F-150 5.0L - DD
Drop Beats NOT Bombs
Joined: Jan 2010
Posts: 1,257
Likes: 0
bump for a nasty single cam.
__________________
http://www.facebook.com/#!/GangsterJoey
Originally Posted by b18c5 
Hard to trust some that spells vtec wrong.
Originally Posted by b18c5 Hard to trust some that spells vtec wrong.
Registered User
Joined: Jul 2010
Posts: 1,545
Likes: 0
VERY CLEAN CAR -- BUMMP FOR YOU___10k? not being a thread basher but ive seen k series on boost with ac going for 8500
__________________
EG 4DOOR BUILT LS SWAP SOLD_Gsr killer
EG HATCH D15B ON BOOST 9PSI TRADED
EK COUPE STOCK......SOLD
DC2 INTEGRA GSR SUPERCHARGED....R.I.P
EK HATCH ALL MOTOR B20 VTEC....SOLD
2002 ALTIMA 3.5 SE 5P ...250 HP...243Tq..SOLD
1998 SUPPPER CLEAN ACCORD_SOLD
2001 MAXIMA SE __ SOLD
00 EM1 B20V FTW F/S__SOLD
03 ACCORD SoLD
1998 EK COuPE Ls-v BOOSTED 367Whp dd..SOLD
2003 TL TYPE S CLONE F/S DD...SOlld
2007 CIVIC SI FG2..FTW..dd SOLD
2005 G35 SEDAN STANCE DD
Oh!? You Mad Son?
DA INTEGRA __ SOLDEG 4DOOR BUILT LS SWAP SOLD_Gsr killer
EG HATCH D15B ON BOOST 9PSI TRADED
EK COUPE STOCK......SOLD
DC2 INTEGRA GSR SUPERCHARGED....R.I.P
EK HATCH ALL MOTOR B20 VTEC....SOLD
2002 ALTIMA 3.5 SE 5P ...250 HP...243Tq..SOLD
1998 SUPPPER CLEAN ACCORD_SOLD
2001 MAXIMA SE __ SOLD
00 EM1 B20V FTW F/S__SOLD
03 ACCORD SoLD
1998 EK COuPE Ls-v BOOSTED 367Whp dd..SOLD
2003 TL TYPE S CLONE F/S DD...SOlld
2007 CIVIC SI FG2..FTW..dd SOLD
2005 G35 SEDAN STANCE DD
Thread
Thread Starter
Forum
Replies
Last Post
NeKe1point0
Proven Power
24
May 31, 2010 05:39 PM
