black 96 acura integra -


car is clean.

good

inside interior clean, tan cloth - real good conditon
short shifter
stage 2 clutch
motor - b18b1
headers | greddy exhaust
intake
new* timing belt
new* oil pump
new* oil catcher
new* rear main seal
new* oil pan gasket
2 new* cv axles
new* main barrings-rod bearings
front springs are coil overs
have back coil overs but not on the car
the back are skunk 2 lowering springs, same
as the front.
have megan racing lowering control arms
rolling on 15's with GT3 gun medal rotos
new* front tires (tire size)195/50/15
power windows, power locks
car comes with radio & four 6x9's
fully built drag racing LS head / $1000
bc 404 cams
bc cam gears
bc stainless steel oversized valves
bc Titanium valve seats
bc dual valve springs
bc TITANIUM retainers


(9.7 of 10) 3 Reviews
Brian Crower Stage 3 Cams

Brian Crower high performance camshafts are ground on state-of-the-art CNC cam grinders to insure accuracy and tolerances to within .02mm. Every BC camshaft profile has been prototyped and dyno tested for proven horsepower results prior to placed into mass production. By grinding cores in high volume, Brian Crower, Inc. is able to pass the cost savings on to the end user. Quality at an affordable price.

Stage 3 Features:
- Longer duration profile.
- Added RPM potential.
- Intended for fully built engine.
- Tuning and ECU mods recommended.
- Requires upgraded springs and retainers.


Crower Cam Gears for the Integra



Crower's new cam sprockets are made from premium 6061-T6 billet aluminum and incorporate a four bolt ARP fastening system to prevent the slippage found in other brands. For the ultimate tuner, Crower sprockets feature 5/16" diameter, 12 point ARP fasteners with a hardened washer to prevent galling and stripping. The lightweight design reduces unwanted harmonics which could cause valve train failure. Price is per cam gear.





Brian Crower Stainless Steel Valves for the Integra



BC valves are made from premium stainless steel with a black nitrate finish, fully machined and swirl polished for ultimate air flow. Dished head for added weight savings and increased valve control at high rpm. Standard and oversize head available.

(9 of 10) 2 Reviews


Acura Integra VALVE LOCKS TITANIUM 5.5MM




.





Brian Crower Valve Springs for the Integra



Designed for high rpm, BC valve springs are wound from only the highest grade, super clean, chrome silicone alloy and feature proprietary processing procedures (chamfer, debur, etc...) for consistent pressures over long term, high rpm useage. Quality valve springs are critical in the prevention of premature valve float.

(10 of 10) 1 Review





Brian Crower Titanium Valve Spring Retainers for the Integra



These retainers are lighter and Brian Crower rates them as three times stronger than stock. If you already have the HKS valve springs or are building a custom setup, these are just the retainers for finishing the job!

(10 of 10) 2 Reviews
bad

paint job is good
although clear coat is pealing off on
-top part of the driver side door
-top part of the driver side roof
-top part of the driver side corner panel
clear coat peal is very small NOT NOTICABLE
back struts are bad
car has no ac
car has no pws [power stering]
but have full ac kit & pws


im looking to trade or sale for very resonable price

Attached ImagesPicture010-9-1.jpg (184.3 KB, 70 views)Picture011-9-1.jpg (80.3 KB, 46 views)Picture012-9-1.jpg (112.1 KB, 41 views)Picture013-8-1.jpg (197.6 KB, 39 views)Picture016-2-1.jpg (193.3 KB, 43 views)