blockguard
Bowley
Joined: Mar 2009
Posts: 363
Likes: 0
my advice fucking get one cause if you do end up fucking up you walls its much more expensive plus if you do it later on then thats more money just to take the head off its much easier to put one on before you but ur engine back together unless it already is
__________________
My Sexy Car Her name is Isis
"Greek for The Throne" 
Robert better not get in my face... 'cause I'll drop that motherfucker!
You're a big, fat, curly-headed fuck!
Suppose Nancy sees me coming out of the shower and decides to come on to me. I'm looking good, got a luscious v of hair going through my chest pubes down to my ball fro. She takes one look at me and goes " Oh my god, I've had the old bull now I want the young calf" and grabs me by the weiner.
My Sexy Car Her name is Isis
"Greek for The Throne" Robert better not get in my face... 'cause I'll drop that motherfucker!
You're a big, fat, curly-headed fuck!
Suppose Nancy sees me coming out of the shower and decides to come on to me. I'm looking good, got a luscious v of hair going through my chest pubes down to my ball fro. She takes one look at me and goes " Oh my god, I've had the old bull now I want the young calf" and grabs me by the weiner.
Smith & Wesson Protected.
Joined: Apr 2006
Posts: 3,617
Likes: 0
They are a waste of money and even the people that make them agree. If you do end up getting one make sure is pressed in before you bore and hone the block. Cause the installation process tends to "egg" shape the cyl cause of the tight fit.
__________________
-Induction Performance
ALPHA Tuned.
-ROQUE MACHINE SHOP For ALL your fabrication needs.
-Induction Performance
ALPHA Tuned.-ROQUE MACHINE SHOP
For ALL your fabrication needs.
engine building &amp;amp;best
Joined: May 2003
Posts: 11,971
Likes: 0
^his right you have to have the engine honed again after you install it.i have only done 2 turbo sohc motors i myself use a blockguard in every motor"thats not stockrebuilt" building a sohc for turbo sucks.buy a ls motor..unless you find a old set of the eagle rods with the Edge sloped and 5/16bolts then you will need to cut the block"also has to be done b4 honeing/boreing"
__________________
i love AUTOZONE
MY CAR iS PROTECTED BY ZOOMBAK GPS LOCATOR IS YOURS?
175+served in engines built from minime to gsr/lsvtec,b16 b20vtec,d15 k24 powerhouses or just rebuilds.life is good
i like when people don't take my advice.cause then i make more money when u need it rebuild the right way!
how many speed holes do i need in my bumper,b4 i can run 15's?
i love AUTOZONE
MY CAR iS PROTECTED BY ZOOMBAK GPS LOCATOR IS YOURS?
175+served in engines built from minime to gsr/lsvtec,b16 b20vtec,d15 k24 powerhouses or just rebuilds.life is good
i like when people don't take my advice.cause then i make more money when u need it rebuild the right way!
how many speed holes do i need in my bumper,b4 i can run 15's?
Registered User
Joined: Jul 2002
Posts: 9,270
Likes: 0
Honestly I have had good success without them and with them installed correctly. They need to be welded in right below the cylinder sleeves and cylinders bored/honed
__________________
- Induction Performance
* IP E-Mail
* IP Face Book
* IP Web-Site
* RIP Kevin/Slo_Si RIP & Pablo/Fathead
- Induction Performance
* IP E-Mail
* IP Face Book
* IP Web-Site
* RIP Kevin/Slo_Si RIP & Pablo/Fathead
