Fs: **built Ls Vtec** $3000 Firm!
Thread Starter
uh oh
Joined: Oct 2003
Posts: 2,307
Likes: 0
Fs: **built Ls Vtec** $3000 Firm!
its time for a new thread. so here it goes...
Motor:
jdm b16 head ported matched and polished
Gsr cams
Golden Eagel cam seal
b18A bottom end
REV valves, springs and retainers
ENDYN rollerwave 9.1-9:5:1 compression turbo pistons
REV rods
ENDYN racing oil pump
Golden Eagle headgasket
acl bearings
ARP rod, head and main bolts
custom step-down dowels, GSR oil pickup, GSR windage tray, GSR oil pan(Golden Eagle Kit)
golden eagle block girdle
golden eagle ls vtec oil conversion
arizona race block guard
short ram intake
skunk 2 intake mani
kamakazi header
b&m fuel pressure reg.
mint j1 tranny
shift linkage
LHT custom mounts
ACT 6 puck, extreme duty pressure plate and 12 lbs. flywheel
aem cam gears
MSD cap, wires and coil
Brand new distributor
chipped pr3 ecu
motor only has 4k miles on it
basically its a complete swap. everything you need to put it in a obd0 car. motor runs perfect and its still in the car if you want to hear it run/drive. no joyrides serious buyers only. i do have receipts for everything. there will be a number of witnesses present at the time of sale so there wont be any of that you sold me a bad motor crap. and you must have some kind of deposit before i pull the motor. and NO i will not part out and NO trades. 3000 FIRM! 727-698-4976 -Keith
for pictures check the links. https://www.tamparacing.com/forums/h...tec-block.html
https://www.tamparacing.com/forums/h...d-project.html
Motor:
jdm b16 head ported matched and polished
Gsr cams
Golden Eagel cam seal
b18A bottom end
REV valves, springs and retainers
ENDYN rollerwave 9.1-9:5:1 compression turbo pistons
REV rods
ENDYN racing oil pump
Golden Eagle headgasket
acl bearings
ARP rod, head and main bolts
custom step-down dowels, GSR oil pickup, GSR windage tray, GSR oil pan(Golden Eagle Kit)
golden eagle block girdle
golden eagle ls vtec oil conversion
arizona race block guard
short ram intake
skunk 2 intake mani
kamakazi header
b&m fuel pressure reg.
mint j1 tranny
shift linkage
LHT custom mounts
ACT 6 puck, extreme duty pressure plate and 12 lbs. flywheel
aem cam gears
MSD cap, wires and coil
Brand new distributor
chipped pr3 ecu
motor only has 4k miles on it
basically its a complete swap. everything you need to put it in a obd0 car. motor runs perfect and its still in the car if you want to hear it run/drive. no joyrides serious buyers only. i do have receipts for everything. there will be a number of witnesses present at the time of sale so there wont be any of that you sold me a bad motor crap. and you must have some kind of deposit before i pull the motor. and NO i will not part out and NO trades. 3000 FIRM! 727-698-4976 -Keith
for pictures check the links. https://www.tamparacing.com/forums/h...tec-block.html
https://www.tamparacing.com/forums/h...d-project.html
__________________
my car gets mad after 5,500 rpm!
cheeSpec tuned!
R.I.P.
Pablo
Lil John
Mario
my car gets mad after 5,500 rpm!
cheeSpec tuned!
R.I.P.
Pablo
Lil John
Mario
90% grind 10% sleep
Joined: Nov 2002
Posts: 6,963
Likes: 0
dont drop the price it was cheap enough
__________________
727-510-6301
Honda Valve Adjustments 50$
I buy and/or Fix Broken Honda transmissions.
I TUNE KPRO AND S300
I DO NOT WORK FOR FREE
E-Z OUT BOLT AND STUD EXTRACTOR: A tool ten times harder than any known drill bit that snaps neatly off in bolt holes thereby ending any possible future use.
727-510-6301
Honda Valve Adjustments 50$
I buy and/or Fix Broken Honda transmissions.
I TUNE KPRO AND S300
I DO NOT WORK FOR FREE
E-Z OUT BOLT AND STUD EXTRACTOR: A tool ten times harder than any known drill bit that snaps neatly off in bolt holes thereby ending any possible future use.
