Same Car, New Powerplant Build

[GB]

Been gathering parts and waiting on the shortblock since February. Should start to go together next week.

347 Liberator Dart Complete Shortblock
Dart SHP Machined Block
Scat 4340 Forged Steel 3.400 Crankshaft
Scat 4340 Forged Steel H Beam Connecting Rods 5.400
Probe SRS 2618 Forged Pistons (15.3cc TFS ONLY) 4.
030
Perfect Circle Moly File Fit Rings
Clevite 77 H Main Bearings
Clevite 77 H Rod Bearings
Dart Coated Cam Bearings
Screw in Oil Galley Plugs
Fel Pro Rear Main Seal
ARP Main Studs
Freeze Plugs
FordStrokers Custom HYD Roller Camshaft
SA Gear Billet Timing Chain w/Torrington Bearing
Melling Oil Pump M68
Moroso Oil Pump Pick up 24519
ARP Billet Oil Pumpshaft
Fel Pro 1 Piece Pan Gasket
Moroso 7qt Oil Pan - 20511
Mr. Gasket Oil Pan Bolts
Timing Chain Cover - Fox Body
Fel Pro Timing Chain Gasket Set
Fuel Pump Eccentric, if using a mechanical fuel pump

Powerbond SFI 28oz Balancer 1060-SS
ARP Balancer Bolt 150-2501
Ford Racing 157 Tooth Billet Steel Flywheel M6375-
A302B
MACHINE BLOCK
-Cylinders bored on Kwik-Way Boring Bar and Table
-Finish honed on Sunnen SV-616 Hone with BHJ
Aluminum Torque Plates, Fel Pro Head Gaskets and ARP
Hardware (.0001-0002 Taper MAX)
-Plateau Brushed (Provides Instant Ring Seal)
-Main Bearing Bores Align Honed on a Sunnen CH-100
Hone
-Deck surfaced on a Winona Van Norman CBN surfacer
(Ra Finish compatible with MLS Gaskets)
-Screw In Oil Galley Plugs
-Lifter Valley Oil Drain Backs Chamferred
-Oil Filter Inlet Chaferred
-Threaded Holes Chased
-Lifter Bores Honed
BALANCE
Crankshaft Balancing done on Hines Dominator XP Digital
Balancer - Balanced to 28oz
BLOCK PAINTED - Cast Aluminum #1650

Aeromotive A1000 Fuel Kit #17147
Moser 31 Spline Axles #MSR-A883151
Moser Axle Bearing Kit #MSR-9563
Digital MSD6AL #6425
Detroit Truetrac #DTL-913A561
Ratech 8.8 Seal Kit Complete #RAT-305K
Ford Motorsport Driveshaft Yoke #FMS-M-4841A
PA130 Amp Altenator #PA-16196B1
Ford Motorsport Water Pump #M-8501-C50
Pro-M 80MM Mass Air Recalibration
Delphi 62 lb Injectors
Bosch O2 Sensors #13942
Trick Flow 8.8 Differential Cover #TFS-8510500
Dorman 620-104 Contour Electric Fan #RNB-620-104
Flex-a-Lite Variable Speed Controller #FLX-33054
Trick Flow 205cc CNC Head Work
Trick Flow R Upper/Lower Intake(Black)
Fel Pro Head Gaskets
Oxygen Sensor Harness-Extended #FH-026E
Tremec TKO600 #TRE-TCET5008
McLeod Clutch Disc 10.5x1 - 1-1/8x26 Kevlar #MCL-260970
Throttle Body Gaskets #BBK-1572
ARP 1/2" Head Studs #ARP154-4003

My S-Trim will be going back on as well. Can't wait to hear it fire up. More pics to come as progress is made.

[GB]

.

[Zman]

ooohhh everything so shinny, looks great.

[diamonddog]

Beautiful build and sounds very well planned. One question .... is the S-trim temporary til an upgrade?

[GB]

For now the S-trim will suffice. Just a street car, not a track car.

[Zman]

but Im not sure if its still a sleeper when you probably will hear it coming.

[GB]

Yeah, I'm going to have to come up with something else.

[Zman]

ah just tell people its an alternator bearing starting to go

[GB]

Been making some progress. Dropped in car yesterday.

[GNs-r-slow]

Edited: I see you bought an assemble SB

[slowmoving1]

nice set up

[GB]

Edited: I see you bought an assemble SB

Yep

[GNs-r-slow]

Are you gonna break it in with the charged disconnected?

[Iraq&Roll]

Break it in on the chassis dyno with boost! Any reason you went with a 4.030 bore and not 4.125?

[GB]

Are you gonna break it in with the charged disconnected?

No, everything will be connected, just going to be easy on it for a little while.