i have a question??????

[customkid72]

so i traded my del sol for a freshly rebuilt turbo crx ....ive been going back and forth with proven power to get my car tunned and between the guy i got this car from... so here was my last straw today i pulled up to pp and one guy notices very light white smoke coming from my vc ....and he calls it blow by so he compression tested the car and with 9 5 1 cp pistons it pulled a 125 130 and 150 and 15o ....so they decide not to tune it...now im going back and forth with the guy i got the car from...and im getting frustrated ...... so heres my question the motor was just put together a 2 weeks ago ....so now my question is...if you rebuild a motor does it take time for rings to fit in your walls properly.that will lead to your comp going up? or is it a bad motor ...the car runs and drives fine...is there a for sure way i can check this?

[Thaking]

honda section

[sleepR_]

On a side note, the thread tltle reminds me of MeSsIeR or however he did his name back in the day

[J@meson]

so i traded my del sol for a freshly rebuilt turbo crx ....ive been going back and forth with proven power to get my car tunned and between the guy i got this car from... so here was my last straw today i pulled up to pp and one guy notices very light white smoke coming from my vc ....and he calls it blow by so he compression tested the car and with 9 5 1 cp pistons it pulled a 125 130 and 150 and 15o ....so they decide not to tune it...now im going back and forth with the guy i got the car from...and im getting frustrated ...... so heres my question the motor was just put together a 2 weeks ago ....so now my question is...if you rebuild a motor does it take time for rings to fit in your walls properly.that will lead to your comp going up? or is it a bad motor ...the car runs and drives fine...is there a for sure way i can check this?

Sounds like it wasnt done properly...

[John]

on a side note, the thread tltle reminds me of messier or however he did his name back in the day

i have a quastion!

[CoRDiTe]

If that motor was just rebuilt you need to break it in. Now if you're abusing it before you break it in then you could do damage to the motor.

[J@meson]

If that motor was just rebuilt you need to break it in. Now if you're abusing it before you break it in then you could do damage to the motor.

meh

[FoxHondaRider]

Built not bought, modified cars aren't for everyone... sucks to be you.

[Nycist]

I personally don't let a car see boost before the rings are seated.....

[customkid72]

the car hasnt been boosted on even tho the whole kit is installed but its on 0 plds

[The Hedgehog]

so i traded my del sol for a freshly rebuilt turbo crx ....ive been going back and forth with proven power to get my car tunned and between the guy i got this car from... so here was my last straw today i pulled up to pp and one guy notices very light white smoke coming from my vc ....and he calls it blow by so he compression tested the car and with 9 5 1 cp pistons it pulled a 125 130 and 150 and 15o ....so they decide not to tune it...now im going back and forth with the guy i got the car from...and im getting frustrated ...... so heres my question the motor was just put together a 2 weeks ago ....so now my question is...if you rebuild a motor does it take time for rings to fit in your walls properly.that will lead to your comp going up? or is it a bad motor ...the car runs and drives fine...is there a for sure way i can check this?

That's more like 4 questions....Honda section is your friend.

On a side note, the thread tltle reminds me of MeSsIeR or however he did his name back in the day

i have a quastion!

meh

the car hasnt been boosted on even tho the whole kit is installed but its on 0 plds

What are plds? Is that some new drug? Or is that a new Turbo Kit?

[BABILLARACING]

if the engine was properly rebuild and you know what you doing you could breaking the engine on the street in couple of hours or on the dyno also .

[*JamReX*]

if the engine was properly rebuild and you know what you doing you could breaking the engine on the street in couple of hours or on the dyno also .

huh/?

[BABILLARACING]

quick breakdown , bearings are properly measure (also breaking coating removed from bearings ) .correct ring gap ,correct honing patern and grid for the type ,material and end use of the rings .This is what i was trying to said .

[*JamReX*]

quick breakdown , bearings are properly measure (also breaking coating removed from bearings ) .correct ring gap ,correct honing patern and grid for the type ,material and end use of the rings .This is what i was trying to said .

and you are a shop owner?