few neon things, 2.4 motor new srt pistons etc..

[neondriver]

i will make a package deal, a 2.4 swap for you do throw in your car...2.4 block complete with water/oil pump pan oil pickup tube, srt-4 pistons/rods, rings, and bearings, with the race head and crane cams, valve cover, motor mount adaptor, and headgasket set all you will need is a main seal and timing belt and you have an awsome 2.4 which can hold well over 400 hp. for 1,500.

im going turbo 2.4 so i dont need my 2.0 parts anymore, im going to be adding parts as i keep going through my garage but this is the bulk of it:


*brand new, just not in the box arp head studs i was told they were for a 2.4 and the 2.4 i just bought already has them. so $80 shipped
*a 97 2.4 stratus computer $45 shipped
*transmission mount i got from a friend is is filled with something and is verry firm. i wanted to use it but i cant on my 2.4 swap $40 shipped
*msd wires, $25 shipped
*stock coil $15 shipped
*brand new never opened 2.0 dohc head gasket kit paid over $100, sell for $75 shipped.
* 2.4 motor mound and the 2.4 adaptor(missing spacers) i forget who made this one but i remember it was expensive.....but this is the mount you can use to mount in a 2.4 to the stock 2.0 passenger side mount $80 shipped both
*booger tranny bushings, only the 2 for the transmission only 1 is in th picture but i have both $5 shipped
*a 2.0 and a 2.4 valve cover, the 2.4 is red and could use a new paint job $45 shipped each
*vibrant front strut bar $40 shipped




==================================
and now the best part! my head off my acr. fully ported and polished, my car on a stock bottom end with this head and a mopar comp with 60mm t/b and crane 16, ran 13.6 in the quarter, it has crane springs and retainers, stock valves and rockers and lifters installed late 2004 (the head has been my garage for about 1.5 years so it is only 3 years old and this car was only driven a cople times a week. ill throw in basically everything: head, valves, crane springs/retainers, cam caps, head bolts, and a red valve cover(or the black one if you want it. ) although its hard to tell in the picture the head is ported and smooth all the way through, i polished about 1" inside when i took it out to clean it up a little when i was planning to re-use it on another 2.0 n/a motor

(it was pretty hard to get a good picture) asking $750
watch my vid in my sig this is the head that was on the car in that video!






------------------------------------------------------------------
still debating, i have crane 16 cams, they have gottan a cople spots of surface rust from sitting, i may use them in my 2.4 or may not. but make offer and i might sell them. they have stock cam gears installed on them

[TdodgeNeon]

send pics to tdodgeneon@yahoo.com want pics

[neondriver]

Originally Posted by TdodgeNeon

send pics to tdodgeneon@yahoo.com want pics

did you want pictures of the motor, car, or valve covers?

[neondriver]

pict of car here: neondriver/95neon - Photobucket - Video and Image Hosting

[TdodgeNeon]

how much for the head on the block, or jus the valve cover

[TdodgeNeon]

price of throttle body?

[neondriver]

just the valve cover and no tb as of now, once i get the motor together ill have alot of extra parts left over....just not sure what ones yet.

[TdodgeNeon]

how much for the valve cover

[neondriver]

45 for the 2.4 and 35 doe the dohc sound ok?

[neondriver]

up dated more parts prices picts etc...

[neondriver]

bushings sold, wires and head are pending. so now the 2.4 motor isnt ava as a whole