88 10th Ann Part Out S5 Swap Exhaust Radiator

[onezx2ner]

I bought an 88 turbo II 10th ann to rebuild the motor and have lost interest in completely the project.


10th Anniversary Shell $1000
Full Interior(missing a few of the usual pieces)
Tokico Adjustable Struts & Intrax Springs
10th Ann Wheels
All the a/c lines and chassis harness are good
just no motor, tranny, wiring harness, radiator, exhaust or ecu

s5 complete turbo II swap $650 (started up fine just needs to be pulled and some seals replaced)
Tranny
Motor(low compression in one housing)
Wiring & 2 ECU(one with a fuel cut defender)
750cc Secondaries
Decent Street Port
Downpipe $50
Downpipe Back Dual Apexi n1 $450 I'll try to polish it up
Koyo Radiator $225

http://i8.photobucket.com/albums/a48/baylymiley/Vehicles/apirl9th008.jpg
http://i8.photobucket.com/albums/a48/baylymiley/Vehicles/rx7001.jpg
http://i8.photobucket.com/albums/a48/baylymiley/Vehicles/rx7002.jpg
http://i8.photobucket.com/albums/a48/baylymiley/Vehicles/rx7003.jpg
http://i8.photobucket.com/albums/a48/baylymiley/Vehicles/rx7005.jpg
http://i8.photobucket.com/albums/a48/baylymiley/Vehicles/rx7006.jpg

[onezx2ner]

Shell maybe going to someone so...yeah do that

[seventhgear]

bump for a hell of a deal.....im interested in the shell if it doesnt sell to the someone u were talking about.... more interior pics would be good though.
thanks

[onezx2ner]

Lots of interest so far. I'm goign to clean up the shell and get some pics to my buddy and then post them here.

[bnr-240sx]

How much u want for the street port?

Will the exhaust fit on a vert?

[onezx2ner]

The Motor set has been sold.

Cleaning up some little body blems and then will take pictures of the shell if my buddy doesn't want it.

[onezx2ner]

OH and downpipe went with the swap as well.

[gardianb0b]

how much for springs/shocks, and drivers seat?

[onezx2ner]

$400 for the Struts and Lowering Springs
I don't have any pictures but they are like brand new and they are the Tokico's with adjustable damping.
Here's the exhaust, still could use a polish
http://i8.photobucket.com/albums/a48/baylymiley/Vehicles/for%20sale/apexi002.jpg
http://i8.photobucket.com/albums/a48/baylymiley/Vehicles/for%20sale/apexi001.jpg

[seventhgear]

i wanna see pics of the shell..... ohh and how much for the exh. again?

[onezx2ner]

Pics of the shell the way it sits tomorrow.

Exhaust $450

[sharingan 19]

is that exhaust stock or is that a test pipe welded onto it?

[onezx2ner]

The exhaust is 3" with a 3" pipe weld where the cat would have been. It was made not a kit.

[sharingan 19]

What kind of dp did you have on there? do you know if it would bolt to an RB 3in dp? Also, is there any way to adjust the exhaust so it doesn't sit way out behind the bumper w/o cutting/re-welding?

[onezx2ner]

I dont know what RB refers to, but it was bolt up to a 3" dp. Also it doesn't sit too far out behind the back bumper I think it sits about perfect.

[sharingan 19]

RB = racing beat

Yours sits just about the same way as most every N1 dual that Ive seen (probably a little better actually) so I guess its just the design of the exhaust. It looks like (and maybe its the picture)the tips stick out like 3-4 in past the bumper. I was hoping they could be made to sit closer to flush.

[seventhgear]

exhaust looks nice! still waiting on some T2 pics tho man!!!! lol post em im still interested.

[zedd]

shell still available?

[onezx2ner]

Pics are up. It has soem surface rust here and there and I work on fixing that day to day. To worst spots is the rocker is dented in on Pass. side and the doors have rust underneath the bumper guards.