H22 Turbo , Top mount GT35R

[MrLHT]

Here's the project we've just finished for all you H22 fans...

The Motor and cylinder head are both fully built.The Motor was already installed when the vehicle came to us.

This Runs a top mount manifold, GT35R , 3" down pipe and a Precision 600hp intercooler half size raidator with Spal fan.
It's running Hondata S300 and Precision 880cc injectors. Dyno soon, should be 500 whp.

Enjoy....

http://i89.photobucket.com/albums/k231/lhtperformance/DSC00130.jpg

http://i89.photobucket.com/albums/k231/lhtperformance/DSC00134.jpg

http://i89.photobucket.com/albums/k231/lhtperformance/DSC00126-1.jpg

http://i89.photobucket.com/albums/k231/lhtperformance/DSC00123.jpg


http://i89.photobucket.com/albums/k231/lhtperformance/DSC00124.jpg

[YARO]

That looks bad ass.

[Ringo_]

:monkspk:

[VOD]

hotness..do u know what internals were used...im just askin cause im not building my motor for boost

[JH26]

thats a bad ass fucking setup right there

[00ACCORD]

Thats the setup I want

[Cold_Beer]

NICE! loving the top mount :thumbup:

[ElSuperSpic]

Nice, just wondering how much $ has been put in to the car with upgrades and engine etc..

[GsEclipse02]

Nice, just wondering how much $ has been put in to the car with upgrades and engine etc..

i would think near the lines of 8g's

[marksaccord95]

aww, reminds me of my h22a turbo accord from like 5 years ago

http://www.accordclub.com/lastmotorpics/recent/P1010038.JPG

[VOD]

i would think near the lines of 8g's
if not more, all said and done its going to run me about about $9500..fully built ground up

[YARO]

i would think near the lines of 8g's
I'll say a couple of more G's

[MrLHT]

I'm not sure on the build price. Laskey built the short block and Portflow did the head. I would think when said and done there's about 10k in the motor.

[Alpha]

Looks great. Any more pictures of the exhaust manifold itself?

[hondamike504]

looks good;)

[hondapower101]

block:sleeved by dan benson
87mm cp pistons
manley turbo tuff rods
balanced and micropolished crank

head:supertech valvetrain
pnp by portflow
built by earl laskey one of his last motors.
there some more stuff but i cant remember.

john the car came out great,ill be back for the final tune pretty soon.
thanks to john wilson and hondamike.
mike i'll stop by sometime to drop off the air intake at your shop.

[hondamike504]

block:sleeved by dan benson
87mm cp pistons
manley turbo tuff rods
balanced and micropolished crank

head:supertech valvetrain
pnp by portflow
built by earl laskey one of his last motors.
there some more stuff but i cant remember.

john the car came out great,ill be back for the final tune pretty soon.
thanks to john wilson and hondamike.
mike i'll stop by sometime to drop off the air intake at your shop.

thanks;) yea you have to take me for a ride:crack: RIP Earl Laskey

[MrLHT]

I forgot to give HondaMike Props , He assembled the whole motor and drive train which was split into about 10 boxes.

[hondamike504]

I forgot to give HondaMike Props , He assembled the whole motor and drive train which was split into about 10 boxes.

Thanks John:bigthumb: ,you forgot about the big salad bowl w/all the nuts&bolts:lol:

[jts67]

yup that's 1 bad ass setup.big ups for my boy's ride.it pulls hard ass fuck.

[slowsohc]

Looks awesome.

[Presidential_Detail]

Any confirmed numbers yet? looks good!

[Green_Lantern]

NICE! loving the top mount :thumbup:
+1 Looks so sick! Nice work yall!

[hondapower101]

i hope we can have confirmed numbers by this week.john the radiator fan still wont kick on,im check the wiring and groung today,could it be possible that the radiator fan sensor went bad?

[MrLHT]

The fan switch did work , Check it's got 12V at the fan itself.

[miguel745]

Hey Thats A Nice Top Mount Mani I My Self Have H22a Accord Swap Turbo Gt35r With A Log Manifold By Drag On The Dyno Made 435 Hp & Tq 315 I Try To Keep My A/c & P/s But I Will Lose Power . I Will Like To Fine Out More About Your Manifold Or Mybe Get One. I Live In The Orlando Area If You Can Get Back At Me For The Info On How Can I Get One. My # Is 407-737-8868 Ask For Jay.

[perryd727]

how much perry 727-944-2051